Directed Electronics Python 450 ESP Скачать руководство пользователя страница 7

Страница: 7 / 44

wiring diagrams

The primary harness supplied with this unit is the standard 12-pin harness used by DEI

security systems. Three

wires in the plug are not used. The upgrade from this unit to a security system would simply require unplugging

and exchanging control units and connecting the necessary wires to the vehicle. The functions of all the wires

that are used in the primary harness are outlined in the following wiring diagram and the wire connections are

described in the wire connection guides.

______

PURPLE

(-) 200

A STARTER RELAY TURN-ON

ORANGE

(-) 200

A ACCESSORY RELAY TURN-ON

PINK

(-) 200

A IGNITION RELAY TURN-ON

YELLOW

(+) IGNITION INPUT TO REMOTE START

RED

(+) CONSTANT POWER

remote start ribbon harness wiring diagram

RED/WHITE

(-)200

A CHANNEL 2 PROGRAMMABLE OUTPUT

RED

(+) CONSTANT POWER INPUT

BROWN

(-) HORN H0NK OUTPUT

OPEN

NO WIRE

BLACK

(-) CHASSIS GROUND INPUT

VIOLET

NO FUNCTION

BLUE

NO FUNCTION

GREEN

NO FUNCTION

BLACK/WHITE

(-)200

A DOMELIGHT SUPERVISION OUTPUT

WHITE/BLUE

(-) REMOTE START ACTIVATION INPUT

WHITE

(+)/(-) SELECTABLE LIGHT FLASH OUTPUT

ORANGE

(-) 500

A ARMED OUTPUT

H1/1

H1/2

H1/3

H1/4

H1/5

H1/6

H1/7

H1/8

H1/9

H1/10

H1/11

H1/12

primary harness (H1) wiring diagram

Содержание Python 450 ESP













































Результаты поиска

Содержание Python 450 ESP

Отзывы:

Похожие инструкции для Python 450 ESP

Бренды по названию

Популярные бренды

Directed Electronics Python 450 ESP, Руководство по установке

Результаты поиска

Содержание Python 450 ESP

Отзывы:

Похожие инструкции для Python 450 ESP

Бренды по названию

Популярные бренды