Dion-Ag F64-90R Скачать руководство пользователя страница 24

Страница: 24 / 38

ADJUSTMENTS

NOTE

: Keep in mind that any maintenance or adjust-

ment described in this manual is the owner’s

sole responsibility.

WARNING: Never remove guards or make

adjustments while machine and/or tractor engine

is running.

WARNING: After making adjustments, check the

machine very carefully for possible loose parts

or bolts. Make sure aIl guards, shields, and doors

are in place and properly secured before starting

the tractor engine

CAUTION: Never perform work on the Rotary

Corn attachment without first Iowering it to the

ground and applying tractor brakes.

NOTE

: If it is necessary to service the bottom of the

machine, safely raise machine with blocs (see

safety section).

GROUND CLEARANCE ADJUSTMENT

In order to prevent an early wear of the machine or a

mechanical break down, it is important to adjust the

ground clearance. For corn harvest, it is recommended

to adjust the ground clearance to 12 inches (30 cm).

This is the actual distance between the ground and the

saw blade. This adjustment is done through the Forage

Harvester’s hydraulic system.

CONVEYOR CHAIN TENSION ADJUST-

MENT FIGURE 28 TO 31

IMPORTANT

: The conveyor chains must be

adjusted before each day of operation and

after the

first breaking-in hour.

NOTE

: Same procedure on the left side.

The maximum chain play must be approximately 1/4”

(6 mm). This measure must be taken at the center of the

chain, as shown in figure 28.

1/4"

Figure 28 Maximum chain play

A spring (item 3) absorbs shocks during operation (figure

31). Check spring tension. It must be pre-compressed

between 19 and 22 mm (3/4” to 7/8”),

when the chain

is completely loosen

NOTE

: This same adjustment must also be car-

ried out on the input chain tightener spring

(Figure 19).

To tighten the chain, simply loosen nut (item 1 in fi-

gure 29) and then tighten bolt (item 2 in figure 30) until

chain tension is appropriate or until nut (item 1) no lon-

ger touches support bracket (item 4 in figure 30). Gap

should be the two should be approximately 1/16” (2 mm)

as shown. Tighten nut (item 1).

Manual No.F6418E996E

Содержание F64-90R







































Результаты поиска

Содержание F64-90R

Отзывы:

Похожие инструкции для F64-90R

Бренды по названию

Популярные бренды

Dion-Ag F64-90R, Руководство оператора

Результаты поиска

Содержание F64-90R

Отзывы:

Похожие инструкции для F64-90R

Бренды по названию

Популярные бренды