manualshive.com logo in svg

Dingsheng Tiangong PY180H, Руководство по эксплуатации

Поделиться
Скачать
Dingsheng Tiangong PY180H Скачать руководство пользователя страница 77

73 

 

driving motor 3, meanwhile control the operating state of driving motor 3; namely, 
driving state and state of free wheel. 

The driving pump is mounted on the transmission, the system pressure is 

controlled by this pump, of which pressure value is 32Mpa.    Both driving motors are 
mounted in the wheel hub of front wheel. 

 
10.2 Front driving axle 

This grader not only has rear axle drive, but also has front axle drive. The 

technical parameters that this grader can reach are

 

identical with that indicated in 

Section 4.5.2, which can increase towing force by 30%. 

 
10.3 Operating instructions 

Here, the section of the front axle drive is introduced in the operating instructions 

for PY180H grader, for the other sections please refer to chapter 7. 

The PY180H grader has three driving types as follows: full axle drive, only rear 

axle drive and only front axle drive. 

The full axle drive means front and rear axles drive at the same time, which can 

only be used to Gear 1 and 2 of forward , gear 1 and neutral gear of reverse. When the 
control lever of transmission is at the other gears, even the switch for front axle drive 
is at open position, the front axle drive will not work. 

The user of full axle drive can operate according to the operating conditions if it 

necessary to increase towing force. 

In order to reduce the damage of rear axle wheel to leveled road surface in fine 

leveling operations, the use can engage the control lever of transmission of rear axle 
on neutral position, while the front axle drive unit can drive whole machine to move 
to carry out scraping operations.   

The control of front axle drive unit of the whole machine as shown in Fig. 61, 

please see Fig. 62 for details of electrical schematic diagram. 

Содержание PY180H

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды