manualshive.com logo in svg

Dingsheng Tiangong PY180H, Руководство по эксплуатации

Поделиться
Скачать
Dingsheng Tiangong PY180H Скачать руководство пользователя страница 67

63 

 

If the grader is not used for about one year, hydraulic oil will be changed in the 

transmission, driving box of rear axle, tandem box and circle worn gear of the blade at 
the same time and change engine oil (see item 8.3.1). 

1.

 

Clean piston rod completely and fill lubricating oil into all oil cups. 

2.

 

Carryout inspection as follows: 
Check oil levels in the engine, transmission, tandem box of rear axle, 
turbine box of blade rotating and hydraulic tank. 

                Check the air pressure of the tyres. 

 
9. Fault analysis and troubleshooting 

As to the maintenance contents listed in the following column of 

“Troubleshooting”, we suggest that you had better notify the Sales & Service Dept. of 
the manufacturer when you consider the maintenance, since our maintenance workers 
are all specially trained, and have special tools to ensure the repairs can be done 
correct and skilled. 

Note:

 Welding of the bearing structural parts on the grader can be only 

undertaken by our Sales & Service Dept. or done in our factory to ensure the structure 
strength. It is unallowed to weld on the bridge and strictly forbidden to connect the 
earth wire of the welding appliance to the bridge. 

 

Fault symptom, analysis of causes and trouble shooting 

Faults Possible 

causes 

Remedies 

1. Problem in fuel system 
a. Air in the fuel system 
 
 
b. Fuel system blocked 
c. No oil supply or intermittent 

oil supply 

d. Abnormal injection of the fuel 

injector 

e. Incorrect advance angle of 

fuel supply 

 
Bleed air in fuel system with fuel 
delivery pump and check the 
system for air leakage. 
Dissemble and clean. 
Check and repair.   
 
Check the spraying condition of 
the fuel injector. 
Check and adjust. 

1.

 

Diesel engine 

1.1 Diesel engine 
fails to start 

2.

 

Deficiency in compression 
pressure 

a.

 

Piston ring worn out 

b.

 

Piston ring gumming 

c.

 

Valve leakage. 

 
 
 
 
d. Too low compression 
temperature  

 
 
Replace the piston ring 
Remove the gumming 
Valve spring broken, elastic 
force decreased, improper valve 
clearance or bad airproof of 
valve connoid, adopt 
corresponding solutions. 
Low ambient temperature, adopt 
methods like preheating to solve.

Содержание PY180H

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды