manualshive.com logo in svg

Dingsheng Tiangong PY180H, Руководство по эксплуатации

Поделиться
Скачать
Dingsheng Tiangong PY180H Скачать руководство пользователя страница 65

61 

 

thread is opposite. 

Note: 

As for some special operating 

conditions, an alternative arrangement of the wheel
may be of advantage. However, it is recommended that follow the advice of the tyre 
manufacturer. 

 
8.12 Steering 

Check the steering system for normal function regularly. 
a. According to the maintenance system (See item 8.4), sealing conditions of the 

bump, cylinder, pipes and joints in the steering system shall be checked and the 
leakage should be eliminated timely.   

b. Check the nuts and bolts of the steering ladder-shaped tension rod and steering 

cylinder for correct assembling and tighten if necessary. 

Note: 

In case that the fault occurs in the hydraulic steering system, stop working. 

The sales service department of the manufacturer or professional staff should be 
informed to repair. 

 
8.13 Hydraulic operating system 

a. According to the maintenance system (See item 8.4), the bump, cylinder, pipes 

and joints in the steering system shall be checked for leakage.   

b. Operating pressure of the hydraulic operating system. All relief valves in the 

entire hydraulic system are set to the correct operating pressure and these settings are 
sealed. If find any faults, the operating pressure would be readjusted by our service 
personnel. If the seals are opened during the guarantee period in the event of damage 
resulted from excessive pressure settings, the guarantee will be ineffective. 

 
8.14 Transmission shaft 

The transmission shaft must be replaced in case that obvious clearance appears 

between centrepiece of universal joints and hitch yoke

 

sleeve, the mounted balance 

weight

 

plate shall not be disassembled, the damage of the weight parts will result in 

unstable running and earlier wear. 

 
8.15 Electrical device of grader   

8.15.1 Work to be done for electrical device   

When beginning to repair the electrical equipment, take notice that the power 

supply shall be disconnected firstly and the electrical equipment shall be stopped. 

8.15.2 Cable   

The cable is an important component part of the electrical system, as a result, 

must be carefully protected from damage. During the maintenance of electrical system, 
the wire must be checked for loosening condition, good contact and the insulating 
material has been damaged or broken. 

 
8.15.3 Three-phase alternator 

Содержание PY180H

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды