manualshive.com logo in svg

Dingsheng Tiangong PY180H, Руководство по эксплуатации

Поделиться
Скачать
Dingsheng Tiangong PY180H Скачать руководство пользователя страница 43

39 

 

8.2.5 Capacity table 

Note:

 All capacities given in the following table are approximate values.   

Subject to observing oil scale on inspection glass or control orifice. 
 

Part Approximate 

capacity 

Fuel tank 

228L 

First filling oil for hydraulic system 

                      First changing oil for hydraulic system 

130L 

80L 

Change and filtrate oil for engine   

22.4L 

First filling oil for torque converter, transmission 

First changing oil for torque converter, transmission 

28L 

21L 

Rear axle   

28L 

Tandem box 

23L (Each side) 

Turbine box   

2.5L 

 

8.3 Check oil level, change oil and filter 

     

Please refer to items 8.2 and 8.2.3 for instructions to lubrication chart and 

maintenance time.   

 
8.3.1 Engine   

Note: If open the machine enclosure on left side of the engine, two oil filters can 

be seen; if open the machine enclosure on right side of the engine, the oil filler and 
three engine oil scale (One located on the oil sump and the rest on speed regulator and 
ejection pump). 

a. Check engine oil level   

Note: 

Generally, the oil consumption of engine oil is very high, so the oil level 

shall be checked twice daily during running in period (about 200h); check the oil level 
once after running in period. The engine oil level shall be checked when the grader is 
on horizontal position. 

Draw out oil scale, clean it with soft cloth, then reinsert it to limit position; then 

draw out the oil scale, here the oil level shall be between the upper and lower marks. 

b. Change engine oil 
Note: The engine oil shall be changed at the hot state, at this time, shall take care 
of not being scalded by draining off hot oil. 
Store the old oil into a suitable container. 
Refilling with fresh engine oil up to the upper mark. 
 
 
 

Содержание PY180H

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды