DIMAT OPU-1 Скачать руководство пользователя

Страница: 67 / 67

OPU-1

UNIVERSAL POWER-LINE CARRIER SYSTEM TYPE OPU-1

GENERAL DESCRIPTION - Rev 7 (May 2019)

67/67

The devices (hosts) of a single local area network are only able to connect directly with

devices that have the same network number in their IP address. If they have a different

network number they are unable to communicate unless there is another device that allows

a connection to be made between the two networks. The IP address of these devices

capable of connecting different networks is the one that in the hosts is identified as the

default gateway.

In this way, to configure the IP address, the subnet mask and the default gateway of the

web server of the OPU-1 terminal and the management computer, it must be considered

whether or not they belong to the same network.

If the OPU-1 terminal and the computer are connected directly or through a LAN (they

belong to the same network), the IP address of each of them must have the same network

number and a different host number, so the subnet mask must be the same for both. The

default gateway does not need to be configured.

If the OPU-1 terminal and the management computer belong to different LANs and the

connection between them is via WAN, their IP addresses may have a different network

number, but both must be connected to some device (default gateway) capable of

interconnecting LANs.

Содержание OPU-1




































































Результаты поиска

Содержание OPU-1

Отзывы:

Похожие инструкции для OPU-1

Бренды по названию

Популярные бренды

DIMAT OPU-1, Общее описание устройства

Результаты поиска

Содержание OPU-1

Отзывы:

Похожие инструкции для OPU-1

Бренды по названию

Популярные бренды