DIMAT OPU-1 страница 21 Скачать руководство пользователя

Страница: 21 / 67

OPU-1

UNIVERSAL POWER-LINE CARRIER SYSTEM TYPE OPU-1

GENERAL DESCRIPTION - Rev 7 (May 2019)

21/67

AMPU

HIGH-FREQUENCY AMPLIFIER

This module contains the wideband output amplifier of 20 W or 40 W and the

alarm circuits for overload or low transmitted-signal level. This module is

located in the 3 s.u. shelf.

The output impedance of the HF amplifier must be consistent with the

bandwidth of the line filter, in this way:

AMPU.00

For line filter with bandwidth of 8, 16 or 24 kHz.

AMPU.02

For line filter with bandwidth of 8, 16 or 32 kHz.

AFPU

LINE FILTER

This module contains the line filter. This module is located in the 3 s.u. shelf.

The bandwidth of the line filter is selected configuring a jumper and two

switches in the 3 s.u. backplane.

WOPU

6 s.u. backplane

It contains three alarm external signalling relays, whose activation condition is

established from the Management System, the main power-supply switch, the

fuses, the power-supply sockets, and the connectors for external connections.

WPPU

3 s.u. backplane

It contains the line transformer, the coaxial connector for making the

connection to the line, the jumpers for selecting the line impedance, the

dummy load, a setting to connect or not the coaxial-cable shield to chassis,

and the jumpers and switches for selecting the bandwidth of the line filter.

The type of backplane depends on the line-filter bandwidth in this way:

WPPU.00

The bandwidth of the line filter may be 8, 16 or 24 kHz.

WPPU.01

The bandwidth of the line filter may be 8, 16 or 32 kHz.

Содержание OPU-1




































































Результаты поиска

Содержание OPU-1

Отзывы:

Похожие инструкции для OPU-1

Бренды по названию

Популярные бренды

DIMAT OPU-1, Общее описание устройства

Результаты поиска

Содержание OPU-1

Отзывы:

Похожие инструкции для OPU-1

Бренды по названию

Популярные бренды