DIMAT OPU-1 страница 31 Скачать руководство пользователя

Страница: 31 / 67

OPU-1

UNIVERSAL POWER-LINE CARRIER SYSTEM TYPE OPU-1

GENERAL DESCRIPTION - Rev 7 (May 2019)

31/67

The terminal can be constituted by either one or two different modules according to the

number of commands. For one or two commands, ABIT.01 module (commands A and B) is

only necessary. For three or four commands, in addition to the previous one, CDIT.01

module (commands C and D) is also necessary.

ABIT.01

This module contains the Digital Signal Processor (DSP), which

generates the guard and command tones and implements a bank of

filters for the reception of commands.

It also has the software necessary for decision making in the

transmission and reception of commands, as well as software for

input/output management, link supervision and the carrying out of tests.

It contains two command input and output circuits together with five

relays for signalling and/or alarm, configurable by the user.

CDIT.01

This module contains two command input and output circuits together

with four relays for signalling and/or alarm, configurable by the user.

Teleprotection system type TPPU

The teleprotection terminal integrated in the digital band and using dual tone is able to

transmit and receive up to four independent commands and in any combination.

The terminal is constituted by a single module.

TPPU.00

This module contains the Digital Signal Processor (DSP) that

generates the encoded signals and implements the necessary

processing circuits for the reception of all the frequencies used.

It also has the software necessary for decision making in the

transmission and reception of commands, as well as software for

input/output management, link supervision and the carrying out of tests.

Two frequencies are assigned to each command signal, and a single

frequency is assigned to the guard signal.

It contains four command input and output circuits together with two

relays for signalling and/or alarm, configurable by the user.

Содержание OPU-1




































































Результаты поиска

Содержание OPU-1

Отзывы:

Похожие инструкции для OPU-1

Бренды по названию

Популярные бренды

DIMAT OPU-1, Общее описание устройства

Результаты поиска

Содержание OPU-1

Отзывы:

Похожие инструкции для OPU-1

Бренды по названию

Популярные бренды