DIMAT OPU-1 Скачать руководство пользователя

Страница: 28 / 67

OPU-1

UNIVERSAL POWER-LINE CARRIER SYSTEM TYPE OPU-1

GENERAL DESCRIPTION - Rev 7 (May 2019)

28/67

2.5.2

Teleprotection terminals

There are several teleprotection terminals, based on the use of digital signal processing.

2.5.2.1

Teleprotection terminal using single tone

The analog teleprotection terminal using single tone is able to transmit and receive in a

4 kHz analog band up to three independent commands and in any combination or up to

four commands according to a certain logic.

Teleprotection system type ABIT-CDIT

The terminal can be constituted by either one or two different modules according to the

number of commands. For one or two commands, ABIT.01 module (commands A and B) is

only necessary. For three or four commands, in addition to the previous one, CDIT.01

module (commands C and D) is also necessary.

ABIT.01

This module contains the Digital Signal Processor (DSP), which

generates the guard and command tones and implements a bank of

filters for the reception of commands.

It also has the software necessary for decision making in the

transmission and reception of commands, as well as software for

input/output management, link supervision and the carrying out of tests.

It contains two command input and output circuits together with five

relays for signalling and/or alarm, configurable by the user.

CDIT.01

This module contains two command input and output circuits together

with four relays for signalling and/or alarm, configurable by the user.

Teleprotection system type TPPU

The terminal is constituted by a single module.

TPPU.00

This module contains the Digital Signal Processor (DSP), which

generates the guard and command tones and implements a bank of

filters for the reception of commands.

Содержание OPU-1




































































Результаты поиска

Содержание OPU-1

Отзывы:

Похожие инструкции для OPU-1

Бренды по названию

Популярные бренды

DIMAT OPU-1, Общее описание устройства

Результаты поиска

Содержание OPU-1

Отзывы:

Похожие инструкции для OPU-1

Бренды по названию

Популярные бренды