DIMAT OPU-1 страница 41 Скачать руководство пользователя

Страница: 41 / 67

OPU-1

UNIVERSAL POWER-LINE CARRIER SYSTEM TYPE OPU-1

GENERAL DESCRIPTION - Rev 7 (May 2019)

41/67

The only manual adjustment required is that of the line and reception filters. The

Management System contains a help menu in which the operations for the adjustment

of these filters are indicated for each channel.

❖

Modulation levels and percentages (analog channel).

The system allows the signal-level percentages assigned to each signal as well as their

input and output levels to be defined. This section also defines the power boosting used

to send the teleprotection signal, as well as the signals of the analog channel that must

be excluded when it is sent.

❖

Signal-level percentages (digital channel).

The system allows the signal-level percentages assigned to the pilot and QAM/OFDM

signals to be defined.

❖

Blocking.

The audio-frequency outputs can be blocked because of pilot loss or excessive noise.

The user can define the signal-to-noise ratio for each output for which blocking must be

effected as well as the value of excess noise which causes the external alarm to be

activated.

❖

Alarms.

The terminal has three alarm signalling relays, with a simple contact, to which an alarm

or combination of alarms can be assigned from the Management System.

❖

Analog optional modules.

From the Management System it is possible to program all the parameters of the

analog optional modules, such as the transmission speed and central frequency of the

modem and speech characteristics, and teleprotection parameters.

❖

Multiplexer

Allows the operative parameters of the data ports of the MQPU module to be

programmed, as well as those of the data and speech ports of the modules of the

optional internal multiplexer. It also makes it possible to de-activate the service

associated to a port, activating it again when necessary.

Содержание OPU-1




































































Результаты поиска

Содержание OPU-1

Отзывы:

Похожие инструкции для OPU-1

Бренды по названию

Популярные бренды

DIMAT OPU-1, Общее описание устройства

Результаты поиска

Содержание OPU-1

Отзывы:

Похожие инструкции для OPU-1

Бренды по названию

Популярные бренды