Troubleshooting Tables
2.
If connections are okay, you must run the SCSI diagnostic
(Chapter 9) or utilities (Chapter 13) to isolate a media or
controller problem.
See Chapter 7 for information on specific storage devices.
Figure 7–3 shows internal cable routing, and Figure 7–5
shows power cable routing. Figure 7–4 shows recommended
SCSI ID settings and drive placement.
Table 10–13 Drive Problems
Symptom
Possible Cause
Corrective Action
Drive does not work.
Two SCSI identifiers
are set to the same ID
number.
In console mode, enter the
SHOW DEVICE command to
check current settings. Reset
each SCSI ID to a unique
number.
A cable is loose.
Verify that all cables
connections are correct and
secure.
A drive is defective.
Run diagnostics to isolate the
fault to a FRU. Replace the
FRU.
Network
Problems
Table 10–14 describes network problems. If the corrective
actions do not correct a problem:
1.
Verify that all cable connections are correct and secure.
2.
Run NI diagnostics in service mode (for extended testing
capabilities). See Chapter 9.
Table 10–14 Network Problems
Symptom
Possible Cause
Corrective Action
An NI error message
appears when verifying
the Ethernet.
A thickwire/10BASET
terminator or cable was
not installed.
Attach an appropriate Ethernet
terminator.
(continued on next page)
10–16
Содержание DEC 3000 600 AXP
