Desert Aire CM3530 Series Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 50

Desert Aire CM3530 Series Скачать руководство пользователя страница 36

36

The fourth page of Analog Inputs shows the readings of the liquid

pressure and temperature. The Liquid P2T is also shown. The

subcooling shown is a calculated value derived from the P2T less

the liquid temperature.

Figure 44

The fifth page of Analog Inputs shows the readings of the pool

temperature sensors. This screen will only be shown if a pool

condenser is supplied.

Figure 45

To return to the I/O STATUS screen, press the

Esc

key.

2.3.3.5.3 Digital Outputs (Binary) (Figure 46 through 48)

The Digital Outputs Screens shows the state of the devices turned

on and off by the control system. The first page shows the state of

the relay contacts on the controller ports J10 and J11.

•

The first line will show the status of C1, the air heat

contact, “On” and “Off”.

•

The second line will show the status of C2, the tower

pump contact, “On” and “Off”.

•

The third line will show the status of C3, the Supply

Blower Starter, “On” and “Off”.

Desert Aire - CM3530 Manual

«
...
34
35
36
37
38
...
»

Содержание CM3530 Series



















































Отзывы:

Нет отзывов