Desert Aire CM3530 Series Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 50

Desert Aire CM3530 Series Скачать руководство пользователя страница 25

25

will run the compressor for 3 seconds. The discharge and suction

pressure are shown on this screen for a check of the current

compressor rotation.

To return to the Commissioning Menu, press the

Esc

key.

Figure 23

2.3.3.3 BMS Setup (Figures 24 through 30)

Selecting the BMS SETUP from the Commissioning Menu displays a set of

screens which determine how the J3 serial port and the Ethernet port will

communicate. The J3 port can be set to drive a remote PGD display terminal,

communicate via Modbus RTU, LON or BACnet MS/TP. The Ethernet port can

be set to send data via Modbus TCP/IP or BACnet IP.

When the J3 port is set for Modbus RTU, pressing the

DOWN

key will display

Figure 25. This screen will allow the address, baud rate and data parameters

to be set. If J3 is set for BACnet MS/TP, pressing the

DOWN

key will display

Figure 26. This screen will allow the BACnet data to be used.

Pressing the

DOWN

key will also display the Ethernet protocol selection,

Figure 27. Setting the Ethernet port for BACnet IP will allow the screen in

Figure 28 to be displayed. This allows the Device ID and Port to be set.

Pressing the

DOWN

key once more displays the Ethernet Network

Configuration, Figure 29. The unit default is DHCP.

Making any changes to the J3 or Ethernet ports will require a power cycle to

have those changes take effect.

While BACnet can be selected for the J3 or Ethernet port, a license file will

need to be loaded into the controller in order for BACnet communication to be

allowed.

To return to the Commissioning Menu, press the

Esc

key.

Desert Aire - CM3530 Manual

«
...
23
24
25
26
27
...
»

Содержание CM3530 Series



















































Отзывы:

Нет отзывов