Desert Aire CM3530 Series Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 50

Desert Aire CM3530 Series Скачать руководство пользователя страница 30

30

84°

83°

Z

one Temperature (°F)

Zone Temperature Control

Unit Setpoint: 84° F
Cooling Deadband: 2° F

Heating Deadband: 2° F

Cooling Differential: 1° F

Heating Differential: 1° F

The cooling requirement is on above (84° F + 2° F) or 86° F and the cooling requirement is off
below (86° F - 1° F) or 85° F.

The heating requirement is on below (84° F - 2° F) or 82° F and the heating requirement is off
above (82° F + 1° F) or 83° F.

Time

82°

85°

86°

Compressor and Heating Off

Heating Required

Compressor Required for Cooling

Cooling Setpoint = Unit Se Cooling Deadband

Unit Setpoint

Cooling Setpoint - Differential

Heating Setpoint =

Unit Setpoint - Heating Deadband

Heating Se Differential

Zone Temperature

Zone Temperature

Figure 33

84°

83°

Pool Water

Temperature (°F)

Pool Water Temperature Control

Pool Water Setpoint: 85° F

Pool Differential: 1° F

Pool Stage Deadband: 2° F

The LC pool condenser is used below the pool water set point and the aux. pool heat is required
below the pool water set point minus the pool stage deadband.

Time

82°

85°

No Pool Heating Required
LC Pool Condenser Heating Only
LC Pool Condenser & Aux. Heating Required

Pool Water Setpoint - Differential

Pool Water Setpoint

Aux. Pool Heating Required -

Differential

Pool Water Setpoint - Pool Stage Deadband = Aux. Pool Heat Required

Figure 34

Desert Aire - CM3530 Manual

«
...
28
29
30
31
32
...
»

Содержание CM3530 Series



















































Отзывы:

Нет отзывов