Desert Aire CM3530 Series Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 50

Desert Aire CM3530 Series Скачать руководство пользователя страница 15

15

Figure 3

2.3 Main Menu (Figure 4)

Pressing the

Esc

key from the Home Screen displays the MAIN MENU (Figure 4). This menu

allows the operator to select the UNIT STATUS, set the Occupancy Schedule, enter the

Service Menu and view the Unit Revision.

To return to the Home Screen, press the

Esc

key.

Figure 4

2.3.1 Unit Status (Figure 5)

Selecting Unit Status from the MAIN MENU displays a text explanation of the unit.

The ROC Available or ROC Unavailable is shown on the first line of this display.

This is based on the state of the digital input #7. A water flow switch or a jumper will

determine if a remote condenser is available for heat rejection. The Occupied state

(either Occupied or Un-Occupied) is shown on the second line along with the state of

the blower. The Unit Status will show one of the following states on the third line.

•

Off / Satisfied

•

Heating Req.

•

Cooling Req.

•

Dehum & Heat

•

Dehum & Cool

•

Low Suct. Pr

Desert Aire - CM3530 Manual

«
...
13
14
15
16
17
...
»

Содержание CM3530 Series



















































Отзывы:

Нет отзывов