Desert Aire CM3530 Series Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 50

Desert Aire CM3530 Series Скачать руководство пользователя страница 11

11

•

Three-terminal valves have one terminal for the “hot” 24 VAC input, a second

terminal for the “neutral” 24 VAC input and the “negative” signal input.

The control signal may also be set for reverse-acting or for 2-10 VDC. Contact

Desert Aire’s service department for recommendations or instructions on how these

options can be implemented.

1.4

CM3530 Controller Overview

Desert Aire’s CM3530 microprocessor controller is a powerful, flexible controller with many

useful features including:

•

Display of room air temperature, relative humidity and refrigerant pressures.

•

Display of equipment operating status such as dehumidification and cooling.

•

Display of alarms for abnormal conditions such as sensor failures or tripped

safety controls.

•

An optional seven-day occupancy timer which can control outdoor air dampers

(if used) to bring in fresh air when the dehumidifier is an occupied state.

•

A convenient, easy-to-understand display interface which allows the operator to

view and change set points and time schedules.

Desert Aire - CM3530 Manual

«
...
9
10
11
12
13
...
»

Содержание CM3530 Series



















































Отзывы:

Нет отзывов