Desert Aire CM3530 Series Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 50

Desert Aire CM3530 Series Скачать руководство пользователя страница 28

28

The forth octet in the address is settable from 000 to 255. Set the octet to the

assigned address of the unit with the zone sensor that is to be used. If data

is being sent from that unit, the ** NETWORK FAULT ** display will change

to “Data is Being Sent”. Now the bottom line of this screen can be modified

from Use “Local Sensor” to Use “Network Sensor”. Adjusting setpoints,

deadbands and differentials will now allow the network sensor to control all

dehumidifiers on the network.

Note that turning off the dehumidifier with the network sensor will cause all

dehumidifiers to fault, as the sensor data will not be available. Before turning

off the dehumidifier with the network sensor, set all other dehumidifiers to Use

“Local Sensor”.

To return to the Commissioning Menu, press the

Esc

key.

Figure 30

2.3.3.4 Tuning – Deadbands (Figure 31 through 34)

Selecting TUNING from the SERVICE MENU displays the DEADBANDS

screen, (Figure 31). The default settings for the dead bands can be modified

on this screen. The Heating Deadband value is subtracted from the Zone

Temperature Setpoint from Section 2.2. This value is the heating set point that

enables the aux heating output. It is also the heating set point for the Air

Heating PID loop. The Cooling Deadband value is the Zone Temperature

Setpoint. This value is the cooling set point. When the zone temperature

exceeds this value, the compressor is required to be used for zone cooling.

If the Pool Heating or Partial Pool options are enabled in the factory

configuration, the Pool Deadband will be displayed. This setting is subtracted

from the Pool Setpoint from Section 2.2. This value will then be used as the

set point to enable the auxiliary pool heating output.

Desert Aire - CM3530 Manual

«
...
26
27
28
29
30
...
»

Содержание CM3530 Series



















































Отзывы:

Нет отзывов