manualshive.com logo in svg

Deprag AST11-1, Руководство по эксплуатации

Поделиться
Скачать
Deprag AST11-1 Скачать руководство пользователя страница 23

 

23

 

7.4  Minimum bending Radius of Screwdriver Cable 

 

ATTENTION

 

Non-observance will cause damage to the screwdriver cable!  
Observe minimum bending radius of screwdriver cable. 

 

At constant motion: 

  Minimum bending radius 90 mm 

At singular motion: 

  Minimum bending radius 45 mm 

Please make sure that there is no mechanical load on the cables during operation.  
To assure best possible contact, the connections of the cable to the sequence 
controller and the screwdriver must be solid. 

 

7.5  Information on programming the Sequence Controller 

The sequence controller AST11 is already pre-configured upon delivery. 
A functioning screw assembly program is already available for the enclosed EC screw-
driver. The screw assembly programs and settings must however be adjusted to the pre-
sent application case. 
Default settings and parameter changes of the screw assembly programs can be done 
directly on the sequence controller AST11, refer to 

8.2.5.4 Menu Screwdriving Sequence

. 

The web interface must be used to modify or create new screw assembly programs refer 
to 

8.3.4.14 Screwdriving sequence

. 

7.6  Functioning of the Sequence Controller AST11 

7.6.1 Operation as Stand-Alone unit with a handheld Screwdriver 

When manually screwdriving, the start of a screwdriving application occurs depending on 
screw type via contact pressure or via the start button. The program indicated in the Set-
up 

 "Type of program choice" menu is started. Program 16 always starts if the program 

switching has been actuated either via key or switch lever. 

7.6.2 Operation with a higher level controller 

7.6.2.1 Operation 

with 

a handheld Screwdriver 

When manually screwdriving, the start of a screwdriving application occurs depending on 
screw type via contact pressure or via the start button. The program indicated in the Set-
up 

 "Type of program choice" menu is started. 

•  If “Inputs” is selected and a program is entered via the inputs of the I/O interface then 

this program will be started (see 

7.6.2.3 Selection and Start of a Screwdriving Pro-

gram via I/O interface

).  

•  If “Fieldbus” is selected and a program is entered via the fieldbus then this program 

will be started. 

 

Program 16 always starts if the program switching has been actuated either via key or 
switch lever. 

Содержание AST11-1



























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды