Denyo DCA-150ESK Скачать руководство пользователя страница 5

Страница: 5 / 79

WARNING

ELECTRIC SHOCK can kill.

■ Do not touch the output terminals during operation

to prevent decease due to electric shock.

* Never touch the output terminals during operation.

If your hands or the machine are wet, it will result

in a death or serious injury.

* When a wiring work is required, be sure to turn OFF

the circuit breaker and stop the machine.

* Keep the output terminal cover closed and the terminal

bolts tightened while the machine is running.

* A low voltage is generated even when the machine is

in low speed idle operation.

Be sure to stop the machine completely.

■ Do not touch the electrical parts in the machine during operation, as it may

lead to death due to electric shock.

* Always close the control panel and tighten the fixing bolts before operating the machine.

* Always close the side door and lock it before operating the machine.

* When opening the control panel for voltage selection, etc., turn OFF the circuit breaker

and stop the machine.

Содержание DCA-150ESK
















































































Результаты поиска

Содержание DCA-150ESK

Отзывы:

Бренды по названию

Популярные бренды

Denyo DCA-150ESK, Инструкция по эксплуатации

Результаты поиска

Содержание DCA-150ESK

Отзывы:

Бренды по названию

Популярные бренды