DEMA E-Royal Modest 2021, Руководство по эксплуатации и обслуживанию

Страница: 58 / 60

Opozorilo pri vzdrževanju
Ko polje hitrosti prikaže nnA , pritisnite + / - , da izberete
0 ali 1. 0 onemogoči funkcijo, medtem ko 1 to omogoča.
Zaslon bo zahteval takojšnje vzdrževanje na podlagi takih
informacij, kot so akumulirana razdalja vožnje in cikli pol -
njenja baterije. Če skupna razdalja vožnje presega 5.000
km (proizvajalec jo lahko prilagodi), se na zaslonu prikaže
simbol SERVICE . Ko se zaslon zažene, se prikaže znak za
nakopičeno vožnjo razdalja utripa 4 sekunde, kar pome -
ni, da je potrebno vzdrževanje. Ko je številka ciklov polnjenja baterije presega 100, bo prikazo -
valnik simbol SERVICE . Ko se zaslon zažene, bo znak za baterijo utripal 4 sekunde, kar pomeni,
da je potrebno vzdrževanje. Funkcijo opozarjanja na vzdrževanje lahko onemogočite: settings
– maintenance alert ( MA ) - 0. Opozorilo o vzdrževanju lahko nastavite tudi prek računalnika.
To zahteva povezavo USB.
Diameter obroča
Položaj hitrosti prikazuje Wd , meritve so v palcih. Napačen premer kolesa lahko
povzroči nepravilnosti hitrosti. Po tej nastavitvi na kratko pritisnite (<0,3 se -
kunde), da vstopite v nastavitveni vmesnik omejitve hitrosti.
Nastavitev omejitve hitrosti
Ko SPL prikaže SPL , polje razdalje prikaže vrednost omejitve hitrosti. Najmanj -
ša hitrost je 12 km/h, največja dovoljena hitrost je 60 km/h. Po nastavitvi na
kratko pritisnite (<0,3 sekunde) za vstop v meni komunikacije baterije.
Povezava z baterijo
Polje hitrosti prikazuje b01 , polje razdalje pa prikazuje omejitev hitrosti. Pri -
tisnite (<0,3 sekunde), da se pomaknete nazaj. Po tej nastavitvi pritisnite
(<0,3 sekunde) za vnos vmesnika pomnilnika za kodo napake. Samo ko je
vzpostavljena komunikacija med akumulatorjem in krmilnikom, se prikažejo
naslednje informacije, sicer bo prikazoval samo
--- .
Koda Opis Enoto Koda Opis Enoto
b01 Temperatura °C b11 Cikel polnjenja/praznenja
b04 Napetost V b12 Najdaljša doba brez polnjenja h
b06 Povprečje A b13 Doba od zadnjega polnjenja H
b07 Preostala kapaciteta Ah d00 Število celic
b08 Polna kapaciteta Ah d01 Napetost celice 1 V
b09 Relativno stanje polnjenja d02 Napetost celice 2 V
b10 Absolutno stanje polnjenja dn Napetost celice n V
11 DISPLAY MANUAL DP C10.UART
After this setting, briefly press (< 0.3
seconds) to enter the setting interface of
backlight brightness.
• Display Backlight Brightness
When the speed field displays bL1, press
/ to choose a figure between 1 and 5.
The figure 1 represents the lowest brightness
while 5 indicates the highest display back-
light brightness.
After this setting, briefly press (< 0.3
seconds) to enter the setting interface of
automatic off time.
• Automatic Off Time
When the speed field displays OFF, press
/ to choose a figure between 1 and 9.
The figures indicate the minutes that it takes
to automatically shut down the display.
After this setting, briefly press (< 0.3
seconds) to enter the setting interface of
maintenance warning.
• Maintenance Warning (can be deacti-
vated)
When the speed field displays nnA, press
/ to choose either 0 or 1. 0 disables the
function while 1 enables it.
1) The display will prompt maintenance
necessity based on such information as the
accumulated riding distance and the battery
charge cycles.
2) When the accumulated total riding dis-
tance exceeds 5,000 km (can be customized
by the manufacturer), the display will show
the symbol
. When the display is
started up, the sign for accumulated riding
distance will flash for 4 seconds, indicating
that maintenance is necessary.
3) When the number of battery charge cy-
cles exceeds 100 (can be customized by the
manufacturer), the display will the symbol
. When the display is started up,
the sign for battery will flash for 4 seconds,
indicating that maintenance is necessary.
4) The maintenance alert function can be
disabled: settings ->maintenance alert (MA)
-> 0. (Maintenance alert can also be set via
a computer. This requires a USB connection.
See also the parameter setting instructions).
PARAMETER SETTING
12 DISPLAY MANUAL DP C10.UART
• Wheel Diameter check
Speed position displays
Wd, The measurements
are in inches. A wrong
wheel diameter can lead
to speed anomalies.
After this setting, briefly
press (< 0.3 seconds) to
enter the setting interface of speed limit.
• Speed Limit Setting
When the speed field
displays SPL, the distance
field displays the value of
the speed limit. Minimum
speed limit is 12km/h,
maximum speed limit is
60km/h.
After setting, Briefly Press (< 0.3
seconds) to enter the menu of battery com-
munication.
• Battery Communication
The speed field displays
b01 and the distance field
displays the speed limit.
Press
(< 0.3 seconds)
to cycle backward. After
this setting, press
(<
0.3 seconds) to enter into
the interface of memory for error code.
1) Only when communication has been
established between the battery and the
controller the following information will be
displayed, otherwise the display will only
show "- - - -".
2) Information on the battery menu:
The speed
field displays
Definition Unit
b01
Current
temperature
℃
b04 Total voltage V
b06 Average current A
b07
Remaining
capacity
Ah
b08 Full capacity Ah
b09
Relative state of
charge
b10
Absolute state
of charge
b11
Charge/
discharge cycle
b12
Longest period
without charge
h
b13
Period since last
charge
h
d00 Cell quantity
d01
Voltage of
cell 1
V
d02
Voltage of
cell 2
V
……… ………
dn
Voltage of
cell n
V
12 DISPLAY MANUAL DP C10.UART
• Wheel Diameter check
Speed position displays
Wd, The measurements
are in inches. A wrong
wheel diameter can lead
to speed anomalies.
After this setting, briefly
press (< 0.3 seconds) to
enter the setting interface of speed limit.
• Speed Limit Setting
When the speed field
displays SPL, the distance
field displays the value of
the speed limit. Minimum
speed limit is 12km/h,
maximum speed limit is
60km/h.
After setting, Briefly Press (< 0.3
seconds) to enter the menu of battery com-
munication.
• Battery Communication
The speed field displays
b01 and the distance field
displays the speed limit.
Press
(< 0.3 seconds)
to cycle backward. After
this setting, press
(<
0.3 seconds) to enter into
the interface of memory for error code.
1) Only when communication has been
established between the battery and the
controller the following information will be
displayed, otherwise the display will only
show "- - - -".
2) Information on the battery menu:
The speed
field displays
Definition Unit
b01
Current
temperature
℃
b04 Total voltage V
b06 Average current A
b07
Remaining
capacity
Ah
b08 Full capacity Ah
b09
Relative state of
charge
b10
Absolute state
of charge
b11
Charge/
discharge cycle
b12
Longest period
without charge
h
b13
Period since last
charge
h
d00 Cell quantity
d01
Voltage of
cell 1
V
d02
Voltage of
cell 2
V
……… ………
dn
Voltage of
cell n
V
12 DISPLAY MANUAL DP C10.UART
• Wheel Diameter check
Speed position displays
Wd, The measurements
are in inches. A wrong
wheel diameter can lead
to speed anomalies.
After this setting, briefly
press (< 0.3 seconds) to
enter the setting interface of speed limit.
• Speed Limit Setting
When the speed field
displays SPL, the distance
field displays the value of
the speed limit. Minimum
speed limit is 12km/h,
maximum speed limit is
60km/h.
After setting, Briefly Press (< 0.3
seconds) to enter the menu of battery com-
munication.
• Battery Communication
The speed field displays
b01 and the distance field
displays the speed limit.
Press
(< 0.3 seconds)
to cycle backward. After
this setting, press
(<
0.3 seconds) to enter into
the interface of memory for error code.
1) Only when communication has been
established between the battery and the
controller the following information will be
displayed, otherwise the display will only
show "- - - -".
2) Information on the battery menu:
The speed
field displays
Definition Unit
b01
Current
temperature
℃
b04 Total voltage V
b06 Average current A
b07
Remaining
capacity
Ah
b08 Full capacity Ah
b09
Relative state of
charge
b10
Absolute state
of charge
b11
Charge/
discharge cycle
b12
Longest period
without charge
h
b13
Period since last
charge
h
d00 Cell quantity
d01
Voltage of
cell 1
V
d02
Voltage of
cell 2
V
……… ………
dn
Voltage of
cell n
V
SI 58 Delovanje in navodila za vzdrževanje koles Delovanje in navodila za vzdrževanje koles