DEMA E-Royal Modest 2021, Руководство по эксплуатации и обслуживанию

Страница: 34 / 60

4.2. Parameter setting
Setting Preparation
When the display is active, press twice (interval < 0.3
seconds). The system will enter the MENU parameter
setting state, in which the display parameters can be
set. Press twice again (interval < 0.3 seconds) to re -
turn to the main menu. If no operation is performed for
10 seconds, the display will return to the normal riding
display. In the parameter setting state, when the pa -
rameter you want to set begins to flash, press + or - to
adjust the parameter value. Briefly press to switch be -
tween the parameters to be set. Press twice (interval
< 0.3 seconds) to exit the submenu.
Data reset
Press twice (interval < 0.3 seconds) – the display en -
ters the MENU state. In the speed field tC is displayed.
If you press , a „y“ is also displayed. Now all temporary
data, e.g. maximum speed ( MAXS ), average speed
( AVG ) and single trip distance ( TRIP ) can be cleared.
Briefly press (< 0.3 seconds) to enter the km/mile set -
ting interface. If the user does not reset the data, the
single trip distance and the accumulated total riding
time will be automatically cleared when the accumulat -
ed total riding time exceeds 99 hours and 59 minutes.
The data will not be cleared when the display’s light-
sensing function is set to 0 or when it is switched off!
Km/Mile
When the speed field displays S7 , press + a - to switch
between km/h and mph, or to set km or mile. After this
setting, briefly press (< 0.3 seconds) to enter the set -
ting interface of light sensitivity. Default display is km.
Light Sensitivity
When the speed field displays bL0 , press + / - to
choose a figure between 0 and 5. The higher the cho -
sen figure, the higher the light sensitivity. After this
setting, briefly press (< 0.3 seconds) to enter the set -
ting interface of backlight brightness.
Display Backlight Brightness
When the speed field displays bL1 , press + / - to choose a
figure between 1 and 5. The figure 1 represents the low -
est and 5 indicates the highest display backlight bright -
ness. After this setting, briefly press (< 0.3 seconds) to
enter the setting interface of automatic off time.
Automatic Off Time
When the speed field displays OFF , press + / - to choose
a figure between 1 and 9. The figures indicate the min -
utes that it takes to automatically shut down the dis -
play. After this setting, briefly press (< 0.3 seconds)
to enter the setting interface of maintenance warning.
Maintenance Warning
When the speed field displays nnA , press + / - to choose ei -
ther 0 or 1. 0 disables the function while 1 enables it. The
display will prompt maintenance necessity based on such
information as the accumulated riding distance and the
battery charge cycles. When the accumulated total rid -
ing distance exceeds 5,000 km (can be customized by the
manufacturer), the display will show the symbol SERVICE .
When the display is started up, the sign for accumulated
riding distance will flash for 4 seconds, indicating that maintenance is necessary. When the num -
ber of battery charge cycles exceeds 100 (can be customized by the manufacturer), the display
will the symbol SERVICE . When the display is started up, the sign for battery will flash for 4 sec -
onds, indicating that maintenance is necessary. The maintenance alert function can be disabled:
settings – maintenance alert ( MA ) – 0. Maintenance alert can also be set via a computer.
This requires a USB connection.
Wheel Diameter check
Speed position displays Wd, The measurements are in inches. A wrong wheel
diameter can lead to speed anomalies. After this setting, briefly press (< 0.3
seconds) to enter the setting interface of speed limit.
Speed Limit Setting
When the speed field displays SPL , the distance field displays the value of
the speed limit. Minimum speed limit is 12km/h, maximum speed limit is
60km/h. After setting, Briefly Press (< 0.3 seconds) to enter the menu of
battery communication.
Battery Communication
The speed field displays b01 and the distance field displays the speed limit.
Press (< 0.3 seconds) to cycle backward. After this setting, press (< 0.3 sec -
onds) to enter into the interface of memory for error code. Only when com -
munication has been established between the battery and the controller the
following information will be displayed, otherwise the display will only show --- .
Code Definition Unit Code Definition Unit
b01 Current temperature °C b11 Charge/discharge cycle
b04 Total voltage V b12 Longest period without charge h
b06 Average current A b13 Period since last charge H
b07 Remaining capacity Ah d00 Cell quantity
b08 Full capacity Ah d01 Voltage of cell 1 V
b09 Relative state of charge d02 Voltage of cell 2 V
b10 Absolute state of charge dn Voltage of cell n V
10 DISPLAY MANUAL DP C10.UART
PARAMETER SETTING
• Items to be Set
1
〉 Data reset
2
〉 Km/mile
3
〉 Light sensitivity
4
〉 Display backlight brightness
5
〉 Automatic off time
6
〉 Maintenance warning settings
7
〉 Check wheel diameter
8
〉 Speed Limit Setting
9
〉 Speed model
10 〉 Battery infromation10 error code
• Setting Preparation
1) When the display is active, press
twice (interval < 0.3 seconds). The system
will enter the MENU parameter setting
state, in which the display parameters can
be set. Press
twice again (interval < 0.3
seconds) to return to the main menu.
2) If no operation is performed for 10 sec-
onds, the display will return to the normal
riding display.
3) In the parameter setting state, when the
parameter you want to set begins to flash,
press / to adjust the parameter value.
Briefly press
to switch between the pa-
rameters to be set. Press twice (interval
< 0.3 seconds) to exit the submenu.
• Data reset
Press twice (interval < 0.3 seconds) –
the display enters the MENU state. In the
speed field tC is displayed. If you press ,
a "y" is also displayed. Now all temporary
data, e.g. maximum speed (MAXS), average
speed (AVG) and single trip distance (TRIP)
can be cleared. Briefly press
(< 0.3 sec-
onds) to enter the km/mile setting interface.
If the user does not reset the data, the single
trip distance and the accumulated total rid-
ing time will be automatically cleared when
the accumulated total riding time exceeds
99 hours and 59 minutes.
* The data will not be cleared when the
display’s light-sensing function is set to 0 or
when it is switched off!
• Km/mile
When the speed field displays S7, press
/ to switch between km/h and mph, or
to set km or mile. After this setting, briefly
press
(< 0.3 seconds) to enter the
setting interface of light sensitivity. Default
display is km.
• Light Sensitivity
When the speed field displays bL0, press
/ to choose a figure between 0 and 5.
The higher the chosen figure, the higher the
light sensitivity.
10 DISPLAY MANUAL DP C10.UART
PARAMETER SETTING
• Items to be Set
1
〉 Data reset
2
〉 Km/mile
3
〉 Light sensitivity
4
〉 Display backlight brightness
5
〉 Automatic off time
6
〉 Maintenance warning settings
7
〉 Check wheel diameter
8
〉 Speed Limit Setting
9
〉 Speed model
10 〉 Battery infromation10 error code
• Setting Preparation
1) When the display is active, press
twice (interval < 0.3 seconds). The system
will enter the MENU parameter setting
state, in which the display parameters can
be set. Press
twice again (interval < 0.3
seconds) to return to the main menu.
2) If no operation is performed for 10 sec-
onds, the display will return to the normal
riding display.
3) In the parameter setting state, when the
parameter you want to set begins to flash,
press / to adjust the parameter value.
Briefly press
to switch between the pa-
rameters to be set. Press twice (interval
< 0.3 seconds) to exit the submenu.
• Data reset
Press twice (interval < 0.3 seconds) –
the display enters the MENU state. In the
speed field tC is displayed. If you press ,
a "y" is also displayed. Now all temporary
data, e.g. maximum speed (MAXS), average
speed (AVG) and single trip distance (TRIP)
can be cleared. Briefly press
(< 0.3 sec-
onds) to enter the km/mile setting interface.
If the user does not reset the data, the single
trip distance and the accumulated total rid-
ing time will be automatically cleared when
the accumulated total riding time exceeds
99 hours and 59 minutes.
* The data will not be cleared when the
display’s light-sensing function is set to 0 or
when it is switched off!
• Km/mile
When the speed field displays S7, press
/ to switch between km/h and mph, or
to set km or mile. After this setting, briefly
press
(< 0.3 seconds) to enter the
setting interface of light sensitivity. Default
display is km.
• Light Sensitivity
When the speed field displays bL0, press
/ to choose a figure between 0 and 5.
The higher the chosen figure, the higher the
light sensitivity.
10 DISPLAY MANUAL DP C10.UART
PARAMETER SETTING
• Items to be Set
1
〉 Data reset
2
〉 Km/mile
3
〉 Light sensitivity
4
〉 Display backlight brightness
5
〉 Automatic off time
6
〉 Maintenance warning settings
7
〉 Check wheel diameter
8
〉 Speed Limit Setting
9
〉 Speed model
10
〉 Battery infromation10 error code
• Setting Preparation
1) When the display is active, press
twice (interval < 0.3 seconds). The system
will enter the MENU parameter setting
state, in which the display parameters can
be set. Press
twice again (interval < 0.3
seconds) to return to the main menu.
2) If no operation is performed for 10 sec-
onds, the display will return to the normal
riding display.
3) In the parameter setting state, when the
parameter you want to set begins to flash,
press / to adjust the parameter value.
Briefly press
to switch between the pa-
rameters to be set. Press twice (interval
< 0.3 seconds) to exit the submenu.
• Data reset
Press twice (interval < 0.3 seconds) –
the display enters the MENU state. In the
speed field tC is displayed. If you press ,
a "y" is also displayed. Now all temporary
data, e.g. maximum speed (MAXS), average
speed (AVG) and single trip distance (TRIP)
can be cleared. Briefly press
(< 0.3 sec-
onds) to enter the km/mile setting interface.
If the user does not reset the data, the single
trip distance and the accumulated total rid-
ing time will be automatically cleared when
the accumulated total riding time exceeds
99 hours and 59 minutes.
* The data will not be cleared when the
display’s light-sensing function is set to 0 or
when it is switched off!
• Km/mile
When the speed field displays S7, press
/ to switch between km/h and mph, or
to set km or mile. After this setting, briefly
press
(< 0.3 seconds) to enter the
setting interface of light sensitivity. Default
display is km.
• Light Sensitivity
When the speed field displays bL0, press
/ to choose a figure between 0 and 5.
The higher the chosen figure, the higher the
light sensitivity.
11 DISPLAY MANUAL DP C10.UART
After this setting, briefly press (< 0.3
seconds) to enter the setting interface of
backlight brightness.
• Display Backlight Brightness
When the speed field displays bL1, press
/ to choose a figure between 1 and 5.
The figure 1 represents the lowest brightness
while 5 indicates the highest display back-
light brightness.
After this setting, briefly press (< 0.3
seconds) to enter the setting interface of
automatic off time.
• Automatic Off Time
When the speed field displays OFF, press
/ to choose a figure between 1 and 9.
The figures indicate the minutes that it takes
to automatically shut down the display.
After this setting, briefly press (< 0.3
seconds) to enter the setting interface of
maintenance warning.
• Maintenance Warning (can be deacti-
vated)
When the speed field displays nnA, press
/ to choose either 0 or 1. 0 disables the
function while 1 enables it.
1) The display will prompt maintenance
necessity based on such information as the
accumulated riding distance and the battery
charge cycles.
2) When the accumulated total riding dis-
tance exceeds 5,000 km (can be customized
by the manufacturer), the display will show
the symbol
. When the display is
started up, the sign for accumulated riding
distance will flash for 4 seconds, indicating
that maintenance is necessary.
3) When the number of battery charge cy-
cles exceeds 100 (can be customized by the
manufacturer), the display will the symbol
. When the display is started up,
the sign for battery will flash for 4 seconds,
indicating that maintenance is necessary.
4) The maintenance alert function can be
disabled: settings ->maintenance alert (MA)
-> 0. (Maintenance alert can also be set via
a computer. This requires a USB connection.
See also the parameter setting instructions).
PARAMETER SETTING
11 DISPLAY MANUAL DP C10.UART
After this setting, briefly press (< 0.3
seconds) to enter the setting interface of
backlight brightness.
• Display Backlight Brightness
When the speed field displays bL1, press
/ to choose a figure between 1 and 5.
The figure 1 represents the lowest brightness
while 5 indicates the highest display back-
light brightness.
After this setting, briefly press (< 0.3
seconds) to enter the setting interface of
automatic off time.
• Automatic Off Time
When the speed field displays OFF, press
/ to choose a figure between 1 and 9.
The figures indicate the minutes that it takes
to automatically shut down the display.
After this setting, briefly press (< 0.3
seconds) to enter the setting interface of
maintenance warning.
• Maintenance Warning (can be deacti-
vated)
When the speed field displays nnA, press
/ to choose either 0 or 1. 0 disables the
function while 1 enables it.
1) The display will prompt maintenance
necessity based on such information as the
accumulated riding distance and the battery
charge cycles.
2) When the accumulated total riding dis-
tance exceeds 5,000 km (can be customized
by the manufacturer), the display will show
the symbol
. When the display is
started up, the sign for accumulated riding
distance will flash for 4 seconds, indicating
that maintenance is necessary.
3) When the number of battery charge cy-
cles exceeds 100 (can be customized by the
manufacturer), the display will the symbol
. When the display is started up,
the sign for battery will flash for 4 seconds,
indicating that maintenance is necessary.
4) The maintenance alert function can be
disabled: settings ->maintenance alert (MA)
-> 0. (Maintenance alert can also be set via
a computer. This requires a USB connection.
See also the parameter setting instructions).
PARAMETER SETTING
11
DISPLAY MANUAL DP C10.UART
After this setting, briefly press (< 0.3
seconds) to enter the setting interface of
backlight brightness.
• Display Backlight Brightness
When the speed field displays bL1, press
/ to choose a figure between 1 and 5.
The figure 1 represents the lowest brightness
while 5 indicates the highest display back-
light brightness.
After this setting, briefly press (< 0.3
seconds) to enter the setting interface of
automatic off time.
• Automatic Off Time
When the speed field displays OFF, press
/ to choose a figure between 1 and 9.
The figures indicate the minutes that it takes
to automatically shut down the display.
After this setting, briefly press (< 0.3
seconds) to enter the setting interface of
maintenance warning.
• Maintenance Warning (can be deacti-
vated)
When the speed field displays nnA, press
/ to choose either 0 or 1. 0 disables the
function while 1 enables it.
1) The display will prompt maintenance
necessity based on such information as the
accumulated riding distance and the battery
charge cycles.
2) When the accumulated total riding dis-
tance exceeds 5,000 km (can be customized
by the manufacturer), the display will show
the symbol
. When the display is
started up, the sign for accumulated riding
distance will flash for 4 seconds, indicating
that maintenance is necessary.
3) When the number of battery charge cy-
cles exceeds 100 (can be customized by the
manufacturer), the display will the symbol
. When the display is started up,
the sign for battery will flash for 4 seconds,
indicating that maintenance is necessary.
4) The maintenance alert function can be
disabled: settings ->maintenance alert (MA)
-> 0. (Maintenance alert can also be set via
a computer. This requires a USB connection.
See also the parameter setting instructions).
PARAMETER SETTING
EN 34 E-bike operation and maintenance manual E-bike operation and maintenance manual