Delta DVS-328 series Скачать руководство пользователя страница 95 | Manualshive

Страница: 95 / 246

background image

D V S M a n a g e d I n d u s t r i a l R a c k Mo u n t E t h e r n e t S wi t c h U s e r Ma n u a l

3 - 7 4

GMRP Configuration

Description

Factory default

Specify whether the GMRP mode is enabled.



Disable:

The GMRP mode is disabled.



Enable:

The GMRP mode is enabled.

Enable

GMRP Port Configuration

Description

Factory default

Interface

This field displays the interface number.

interface number

Port GMRP Mode

Specify whether the GMRP mode is enabled on the interface.



Disable:

The GMRP mode on the interface is disabled.



Enable:

The GMRP mode on the interface is enabled.

Enable

3.5.6

Multicast Forwarding Table

The multicast MAC address can be added manually, and it also can be added by the GMRP function. This
multicast forwarding table can display the type of the MAC address.

Multicast Forwarding Table

Item

Description

Auto-refresh

Checkmark this box, it will refresh the multicast forwarding table automatically.

VLAN ID

The field displays the identifier of VLAN.

MAC Address

The field displays the multicast MAC address.

Type

The field displays that the learning type is static or dynamic.

Forwarding Interfaces

The field displays the forwarding interface number.

3.6

Traffic Prioritization

The traffic prioritization allows you to make sure that the time-sensitive and system-critical data can be
transferred with the minimal delay. It uses four queues that are present in UI from the high priority to the low
priority.
The Delta switch supports the DSCP trust mode, the 802.1p trust mode, the queue scheduling (Support
Weighted Round Robin and Strict-Priority) and 4 level priority queues. The traffic prioritization depends on 2
methods:



IEEE 802.1P:

a layer 2 marking scheme.



Differentiated Services (DiffServ):

a layer 3 marking scheme.

IMPORTANT

:

Make sure that you save the configuration in the Save Configuration
page after you have applied the configuration changes. (Save
Config



Save Configuration) If you do not save the configuration,

then the configuration will be cleared after the switch is rebooted.

«
...
93
94
95
96
97
...
»

Содержание DVS-328 series























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DVS-328 series

Бренд: Observint Страницы: 11

Бренд: Lab.gruppen Страницы: 35

Бренд: Belkin Страницы: 72

Бренд: Helmholz Страницы: 28

Бренд: Ravpower Страницы: 27

TE100-S16 - 10/100Mbps Ethernet Switch

Бренд: TRENDnet Страницы: 15

Бренд: YATO Страницы: 96

Бренд: ActionTec Страницы: 115

D-NVR4108HS-4KS2/L

Бренд: Dahua Страницы: 33

Бренд: BHU NETWORKS Страницы: 75

Бренд: Tripp Lite Страницы: 3

CyberPower RMCARD201

Бренд: CyberPower Страницы: 8

Бренд: NETGEAR Страницы: 20

GlobeSurfer X-1

Бренд: Option Audio Страницы: 30

Бренд: Ryobi Страницы: 44

Бренд: QNAP Страницы: 11

Бренд: Tripp Lite Страницы: 2

Бренд: NetApp Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды