background image

A p p e n d i x   C   E t h e r N e t / I P  

C - 1 9  

(The value is mapping the 
number of ports in Switch 
device) 

Instance Attributes 

Attr ID 

Access Rule 

Name 

Data Type 

Description of Attribute 

Get 

Interface Speed 

UDINT 

Interface speed currently 
in use 
Speed in Mbps (e.g., 0, 
10, 100, 1000, etc.)       

Get   

Interface Flags 

DWORD 

Interface status flags   

Get 

Physical Address 

ARRAY of 6 USINTs 

MAC layer address   

Get 

Interface Counters 

STRUCT of: 

 

 

In Octets 

UDINT 

Octets received on the   
interface   

In Ucast Packets 

UDINT 

Unicast packets received 
on the interface   

In Nucast Packets 

UDINT 

Non-unicast packets 
received on the interface   

In Discards 

UDINT 

Inbound packets received 
on the interface but 
discarded   

In Errors 

UDINT 

Inbound packets that 
contain errors (does not 
include In Discards) 

In Unknown Protos 

UDINT 

Inbound packets with   
unknown protocol   

Out Octets 

UDINT 

Octets sent on the 
interface   

Out Ucast Packets 

UDINT 

Unicast packets sent on 
the interface   

Out Nucast Packets 

UDINT 

Non-unicast packets sent 
on the interface   

Out Discards 

UDINT 

Outbound packets 
discarded   

Out Errors 

UDINT 

Outbound packets that 
contain errors 

Get 

Media Counters 

STRUCT of: 

Media-specific counters   

Alignmenet Errors 

UDINT 

Frames received that are 
not an integral number of 
octets in length   

FCS Errors 

UDINT 

Frames received that do 
not pass the FCS check 

Single Collisions 

UDINT 

Successfully transmitted 
frames which experienced 
exactly one collision 

Multiple Collisons 

UDINT 

Successfully transmitted 
frames which experienced 
more than one collision 

SQE Test Errors 

UDINT 

Number of times SQE test 
error message is 
generated   

Содержание DVS-328 series























































































































































































































































Отзывы: