Delta Tau PMAC2A-PC/104 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 72

background image

PMAC2A-PC/104

Introduction

3

ACC-2P: Communications Board

Without any options the PMAC2A-PC/104 communicates
through the RS-232 serial interface using the optional ACC-
3L flat cable. Only one method of communication is allowed
at a time.

ACC-2P Option 1A: USB Interface

Option 1A it provides a 12 Mbit/sec USB interface allowing
USB communications with the PMAC2A-PC/104 motion
controller.

ACC-2P Option 1B: Ethernet Interface

Option 1B provides a 10 Mbit/sec Ethernet interface allowing
Ethernet communications with the PMAC2A-PC/104 motion
controller.

ACC-2P Option 2: DPRAM circuitry

Option 2 provides an 8K x 16 dual-ported RAM for USB, Ethernet or PC/104 ports on board of the ACC-
2P communications board. If using for USB or Ethernet communications, ACC-2P-Opt-1A or ACC-2P-
Opt-1B must be ordered. If used for PC/104-bus communications, PMAC2A-PC/104-Opt-2A must be
ordered. The key component installed with this option is U17.

PMAC2A-PC/104 Base Board shown
stack with the Option-1P and
Option-2P boards

«
...
7
8
9
10
11
...
»

Содержание PMAC2A-PC/104









































































Отзывы:

Нет отзывов

Похожие инструкции для PMAC2A-PC/104

Бренд: XMG Страницы: 5

Бренд: NAD Страницы: 2

inLab Speedcure 9494800

Бренд: Dentsply Sirona Страницы: 91

Avenue Express Control Panel

Бренд: Ensemble Designs Страницы: 19

kontron COMe-cEL6

Бренд: S&T Страницы: 99

Бренд: IFM Electronic Страницы: 14

Бренд: Aaeon Страницы: 72

Бренд: AXAGO Страницы: 2

Бренд: Renesas Страницы: 76

Бренд: NEC Страницы: 70

Бренд: Ista Страницы: 16

Бренд: ICP DAS USA Страницы: 31

Бренд: ICOP Technology Страницы: 42

Бренд: Flexwatch Страницы: 13

Бренд: DAPAudio Страницы: 33

ReadyNAS Duo v2

Бренд: NETGEAR Страницы: 100

Бренд: Proxim Страницы: 45

11th Gen Intel Core U-Series

Бренд: IBASE Technology Страницы: 70

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды