Delta Tau PMAC2A-PC/104 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 72

background image

PMAC2A-PC/104

ACC-1P Hardware Reference Summary

34

J4 - Machine Connector (JMACH2 Port)

This machine interface connector is labeled JMACH2 or J4 on the PMAC. It contains the pins for four
channels of machine I/O: end-of-travel input flags, home flag and pulse-and-direction output signals. In
addition, the B_WDO output allows monitoring the state of the Watchdog safety feature.

1.  34-pin female flat cable connector. T&B Ansley P/N 609-3441
2.  Standard flat cable stranded 34-wire. T&B Ansley P/N 171-34
3.  Phoenix varioface module type FLKM 34 (male pins) P/N 22 81 06 3

J7 - General-Purpose Digital Inputs and Outputs (JOPT Port)

ACC-1P’s JOPT connector provides eight general-purpose digital inputs and eight general-purpose digital
outputs. Each input and each output has its own corresponding ground pin in the opposite row. The 34-
pin connector was designed for easy interface to OPTO-22 or equivalent optically isolated I/O modules.
Delta Tau's Accessory 21F is a six-foot cable for this purpose.

1.  34-pin female flat cable connector. T&B Ansley P/N 609-3441
2.  Standard flat cable stranded 34-wire. T&B Ansley P/N 171-34
3.  Phoenix varioface module type FLKM 34 (male pins) P/N 22 81 06 3

J8 – Handwheel / Pulse and Direction Port (JHW / PD Port)

This port provides an extra encoder input or a set of pulse and direction outputs, and its function is
selectable by jumpers.

1.  10-pin female flat cable connector. T&B Ansley P/N 609-1041
2.  Standard flat cable stranded 10-wire. T&B Ansley P/N 171-10
3.  Phoenix varioface module type FLKM 10 (male pins) P/N 22 81 01 8

TB1 – Power Supply Terminal Block (JPWR Connector)

In almost in all cases the PMAC2A-PC/104 will be powered from the PC/104 bus when it is installed in a
host computer’s bus, or from the JMACH1 connector. This terminal block may be used as an alternative
power supply connector or to easily measure the voltages applied to the board.

1. 4-pin terminal block, 0.150 pitch

LED Indicators

D6:

when this green LED is lit it indicates that the watchdog timer has tripped and shut down the PMAC.

«
...
38
39
40
41
42
...
»

Содержание PMAC2A-PC/104









































































Отзывы:

Нет отзывов

Похожие инструкции для PMAC2A-PC/104

Бренд: Ubiquiti Страницы: 23

Бренд: Nvidia Страницы: 115

Wisenet PRN-6400B4

Бренд: Hanwha Techwin Страницы: 14

Бренд: ZALMAN Страницы: 9

Fan Tray 8820-S2-900

Бренд: Paradyne Страницы: 6

Бренд: Xmart Страницы: 8

Бренд: addlink Страницы: 9

1394 Dual-Port CardBus

Бренд: SIIG Страницы: 8

Бренд: Comelit Страницы: 19

CNPS7000C Series

Бренд: ZALMAN Страницы: 8

Zypad WL15 Series

Бренд: Eurotech Страницы: 2

Бренд: AXIOMTEK Страницы: 2

FireWire 800 ExpressCard 34

Бренд: LaCie Страницы: 24

Mustang-M2AE-MX1

Бренд: IEI Technology Страницы: 58

Бренд: Xtreme Страницы: 83

Бренд: Altera Страницы: 40

Бренд: Milesight Страницы: 15

Бренд: Quadram Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды