Delta Tau PMAC2A-PC/104 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 72

background image

PMAC2A-PC/104

Machine Connections

14

Dry Contact

Flag_1_2_V

1

7

JMACH2

PLIM+

5 – 24 VDC

Power Supply

+

-

5-24 Volts proximity

Flag_1_2_V

1

7

JMACH2

PLIM+

5 – 24 VDC

Power Supply

+

-

DAC Outputs Power Supply

0.3A @ +12 to +15V (4.5W)
0.25A @ -12 to -15V (3.8W)
(Eight-channel configuration)

•

The host computer provides the ±12 Volts power supply in the case PMAC is installed in the
PC/104 bus. With the board stack into the bus, it will automatically pull ±12V power from the
bus and it cannot be disconnected. In this case, there must be no external ±12V supply, or the
two supplies will "fight" each other, possibly causing damage. This voltage could be measured
on the TB1 terminal block.

•

In a stand-alone configuration, when PMAC is not plugged in a computer bus, it will need
an external ±12 Volts supply only when the digital-to-analog converter (DAC) outputs are
used

. The ±12V lines from the supply, including the ground reference, can be brought in either

from the TB1 terminal block or from the JMACH1 connector.

Flags Power Supply

Each channel of PMAC has five dedicated digital inputs on the machine connector: PLIMn, MLIMn
(overtravel limits), HOMEn (home flag), FAULTn (amplifier fault), and USERn. A power supply from 5
to 24 Volts must be used to power the circuits related to these inputs. This power supply can be the same
used to power PMAC and can be connected from the TB1 terminal block or the JMACH1 connector.

Over-travel Limits and Home Switches

When assigned for the dedicated uses, these signals provide important safety and accuracy functions.
PLIMn and MLIMn are direction-sensitive over-travel limits that must conduct current to permit motion
in that direction. If no over-travel switches will be connected to a particular motor this feature must be
disabled in the software setup through the PMAC Ix25 variable.

Types of overtravel Limits

PMAC expects a closed-to-ground connection for the limits to not be considered on fault. This
arrangement provides a failsafe condition. Usually, a passive normally close switch is used. If a
proximity switch is needed instead, use a 5 to 24 Volts normally closed to ground NPN sinking type
sensor.

Home switches

While normally closed-to-ground switches are required for the overtravel limits inputs, the home switches
could be either normally close or normally open types. The polarity is determined by the home sequence

«
...
18
19
20
21
22
...
»

Содержание PMAC2A-PC/104









































































Отзывы:

Нет отзывов

Похожие инструкции для PMAC2A-PC/104

Бренд: XMG Страницы: 5

Бренд: NAD Страницы: 2

Бренд: Garland Страницы: 6

Hotwire 8775 MSDSL

Бренд: Paradyne Страницы: 10

RocketCache 3240X8

Бренд: HighPoint Страницы: 17

5200 Live Series EventCD

Бренд: MF DIGITAL Страницы: 21

Бренд: National Instruments Страницы: 80

Бренд: Advantech Страницы: 108

Бренд: Xenteq Страницы: 16

Бренд: Maxtor Страницы: 2

Бренд: EZCast Pro Страницы: 4

Бренд: ekwb Страницы: 2

Бренд: ETAS Страницы: 36

Бренд: Cypress Semiconductor Страницы: 9

Бренд: R.V.R. Elettronica Страницы: 171

RJModem MT5656RJ

Бренд: Multi-Tech Страницы: 27

Бренд: PairGain Страницы: 76

Бренд: BenQ Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды