manualshive.com logo in svg

Delta Tau PMAC2A-PC/104, Руководство по установке, Страница: 28 / 72

Поделиться
Скачать
Delta Tau PMAC2A-PC/104 Скачать руководство пользователя страница 28

PMAC2A-PC/104

 

 

 

PMAC2A-PC/104 Software Setup

 

22 

PMAC2A-PC/104 SOFTWARE SETUP 

 

Note: 

The PMAC2A-PC/104 requires the use of V1.17 or newer firmware.  There are 
few differences between the previous V1.16H firmware and the V1.17 firmware 
other than the addition of internal support for the Flex CPU design. 

Communications 

Delta Tau provides software tools that allow communicating with of the PMAC2A-PC/104 board either 
by its standard RS-232 port or the optional USB or Ethernet ports.  PEWIN is the most important in the 
series of software accessories, and it allows configuring and programming the PMAC for any particular 
application. 

PMAC I-Variables 

PMAC has a large set of Initialization parameters (I-variables) that determine the "personality" of the card 
for a specific application.  Many of these are used to configure a motor properly.  Once set up, these 
variables may be stored in non-volatile EAROM memory (using the 

SAVE

 command) so the card is 

always configured properly (PMAC loads the EAROM I-variable values into RAM on power-up).   
The programming features and configuration variables for the PMAC2A-PC/104 are fully 
described in the PMAC2 User’s and Software manuals. 

Operational Frequency and Baud Rate Setup 

 

Note: 

Older PMAC boards required a start-up PLC for setting the operational frequency 
at 80 MHz. 

That method is not compatible with the PMAC2A-PC/104 board 

and will shutdown the board when used.

 

 
The operational frequency of the CPU can be set in software by the variable I46.  If this variable is set to 
0, PMAC firmware looks at the jumpers E2 and E4 to set the operational frequency for 40, 60, and 80 
MHz operation.  If I46 is set to a value greater than 0, the operational frequency is set to 10MHz * (I46 + 
1), regardless of the jumper setting.  If the desired operational frequency is higher than the maximum 
rated frequency for that CPU, the operational frequency will be reduced to the rated maximum.  It is 
always possible to operate the Flex CPU board at a frequency below its rated maximum. 
I46 is only used at power-up/reset, so to change the operational frequency, set a new value of I46, issue a 

SAVE

 command to store this value in non-volatile flash memory, then issue a 

$$$

 command to reset the 

controller. 
To determine the frequency at which the CPU is actually operating, issue the 

TYPE

 command to the 

PMAC.  The PMAC will respond with five data items, the last of which is “

CLK X

n

”, where “

n

” is the 

multiplication factor from the 20 MHz crystal frequency (not 10 MHz).  “

n

” should be equivalent to 

(I46+1)/2 if I46 is not requesting a frequency greater than the maximum rated for that CPU board.  “

n

” 

will be “2” for 40 MHz operation, “4” for 80 MHz operation, and “8” for 160 MHz operation. 
If the CPU’s operational frequency has been determined by (a non-zero setting of) I46, the serial 
communications baud rate is determined at power-up/reset by variable I54 alone according to the 

Содержание PMAC2A-PC/104









































































Отзывы:

Нет отзывов