Delta Tau PMAC2A-PC/104 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 72

Delta Tau PMAC2A-PC/104 Скачать руководство пользователя страница 48

PMAC2A-PC/104

Base Board E-Point Jumper Descriptions

42

E8: Phase Clock Lines Output Enable

E Point and

Physical Layout

Location Description

Default

E8

B1

Jump pin 1 to 2 to enable the PHASE
clock line on the J8 connector,
allowing synchronization with another
PMAC.

Remove jumper to disable the PHASE
clock line on the J8 connector.

No Jumper

E9: Servo Clock Lines Output Enable

E Point and

Physical Layout

Location Description

Default

E9

B1

Jump pin 1 to 2 to enable the SERVO
clock line on the J8 connector,
allowing synchronization with another
PMAC.

Remove jumper to disable the SERVO
clock line on the J8 connector.

No Jumper

E10 – E12: Power-Up State Jumpers

E Point and

Physical Layout

Location Description

Default

E10

E12

E5

Remove jumper E10;
jump E11;
jump E12;
to read flash IC on power-up/reset

Other combinations are for factory
use only; the board will not operate
in any other configuration

No E10 jumper
installed;

jump E11 and E12

«
...
46
47
48
49
50
...
»

Содержание PMAC2A-PC/104









































































Отзывы:

Нет отзывов