Delta Tau PMAC Mini Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 108

background image

PMAC Quick Reference Guide

Motion Programs

59

•

100

%

Online or CMD command that restores the real-time reference (1 msec =

1

msec).

•

M197 = I10

Suggested M-Variable for time base change. Equal to I10 is 100%, equal

to 0 is 0%.

The variable Ix94 controls the rate at which the time base changes:

23

2

2

t

I10

Ix94

⋅

=

, where t is the slew rate

time in msec.

External Time Base Control (Electronic Cams)

The time reference of each coordinate system can be changed from the default internal reference,
controlled by the

%

command and variables Mx97, to an external source (usually a frequency reference

from a master encoder). A simple change of the variable Ix93 allows switching between the internal time
base and an external source. In this fashion, motion programs can be developed and tested running in
real-time (internal time base) and synchronized later to a master frequency when proven to be functional
and completed.

The only setup part of this feature is an entry in the conversion table that will also indicate a scale factor
for the maximum frequency that the master can possibly input to PMAC. This maximum frequency will
represent 100% or real time.

Position Following (Electronic Gearing)

PMAC has several methods of coordinating the axes under its control to axes not under its control. The
simplest method is basic position following. This is a motor-by-motor function, not a coordinate system
function as time-base following. An encoder signal from the master axis (which is not under PMAC’s
control) is fed into one of PMAC’s encoder inputs. Typically, this master signal is either from an open-
loop drive or a handwheel knob. Ix05 and Ix06 control this function.

Cutter Radius Compensation

PMAC provides the capability for performing cutter (tool) radius compensation on the moves it performs.
This compensation can be performed among the X, Y, and Z-axes, which should be physically
perpendicular to each other. The compensation offsets the described path of motion perpendicular to the
path by a programmed amount. Cutter radius compensation is valid only in

LINEAR

and

CIRCLE

move

modes. The moves must be specified by

F

(feedrate), not

TM

(move time). PMAC must be in move

segmentation mode (I13 > 0) to do this compensation. (I13 > 0 is required for

CIRCLE

mode anyway.)

Program commands

CC0

,

CC1

,

CC2

,

CCR

and

NORMAL

control this feature.

«
...
65
66
67
68
69
...
»

Содержание PMAC Mini













































































































Отзывы:

Нет отзывов

Похожие инструкции для PMAC Mini

Бренд: Barracuda Networks Страницы: 2

Бренд: Udoo Страницы: 7

Бренд: BSS Audio Страницы: 20

Бренд: Reeven Страницы: 2

Бренд: Taiwan Commate Computer Inc. Страницы: 29

Бренд: ZALMAN Страницы: 9

eBOX532-100-FL Series

Бренд: AXIOMTEK Страницы: 2

Бренд: IBM Страницы: 72

Бренд: UNICORECOMM Страницы: 19

Бренд: swiftech Страницы: 2

Бренд: Altera Страницы: 40

Бренд: Milesight Страницы: 15

PCI-AD-x16HE-BG4

Бренд: Serial Cables Страницы: 18

BPN-SAS3-116A-N10

Бренд: Supermicro Страницы: 8

Switch Polarization Print HPP4

Бренд: Domburg Страницы: 11

Бренд: StarTech.com Страницы: 4

SIMATIC NET RUGGEDCOM RX1500

Бренд: Siemens Страницы: 66

Бренд: Siemens Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды