Delta OHM HD32MT.3, Руководство по эксплуатации

Страница: 53 / 62

HD32MT.3
- 53 -
V1.2
LP S1 Position bracket for pyranometers LP PYRA 02 and LP PYRA 10, suitable for
Ø 40 mm to Ø 50 mm rod.
LP PYRA 03S Second class pyranometer according to ISO 9060. Includes: bubble level for
alignment and Calibration Report. RS485 serial output with MODBUS-RTU
protocol. 5÷30Vdc power supply. Upon request, CPM12-8P… 2, 5 or 10 m
cables with 8-pole M12 female connector.
LP SP2 Protection shield for pyranometer LP PYRA 03.
LP SILICON- Pyranometer with silicon photodiode. mV output. Equipped with base with
PYRA 04BL bubble level. Needs a converter/amplifier with standard 0…10 V or 4…20 mA
output for connection to the data logger.
HD2003.79K Kit for fastening pyranometers to the Ø 40 mm rod, includes bushing and
flange.
LP SD18.1 Sensor for the measurement of the solar radiation duration, referred to the
120 W/m 2 threshold of direct radiation, according to OMM indications. The
sensor has no moving parts. RS485 MODBUS-RTU output and free-potential
contact output. 7…30 Vdc power supply. It can be fastened to a rod with a
proper accessory, or installed on a horizontal surface by means of the op-
tional fixing base. Integrated bubble level for alignment. It doesn’t require
position adjustments during the year. Equipped with anti-condensation sys-
tem (1W @ 12 Vdc if connected). 8-pole M12 connector. Upon request,
standard 2, 5 or 10m cables with female free connector. Heating option
available.
CP 18… 12-pole cable. Length: 5 or 10 m. 8-pole M12 connector on one side, free
wires on the other. For LP SD18.1.
LP SD18.O Base for installation of the sunshine duration sensor on a horizontal surface.
Two adjustable feet and one fixed foot. Allows sensor inclination up to 80° to
the vertical, in order to adapt it to the sun position at the latitude of the in-
stallation site.
LP SD18.V1 Support for installation of the sunshine duration sensor on a Ø 40 mm rod.
Allows sensor inclination up to 80° to the vertical, in order to adapt it to the
sun position at the latitude of the installation site.
Rainfall quantity
HD2013
Tipping bucket rain gauge, 400cm 2 area, for temperature ranging from 4°C
to +60 °C. Standard resolution 0.2 mm. 0.1 or 0.5 mm on request with or-
der. Normally closed output contact.
HD2013R Tipping bucket rain gauge, 400cm 2 area, with heater for temperature ranging
from -20 to +60 °C. Standard resolution 0.2 mm. 0.1 or 0.5 mm on request
with order. Normally closed output contact. Supply voltages: 12 Vdc or
24 Vdc ±10% / absorbed power 165 W.
HD2015 Tipping bucket rain gauge, 200cm 2 area, for temperature ranging from 4°C
to +60 °C. Standard resolution 0.2 mm. 0.1 or 0.5 mm on request with or-
der. Normally closed output contact.
HD2015R Tipping bucket rain gauge, 200cm 2 area, with heater for temperature ranging
from -20 to +60 °C. Standard resolution 0.2 mm. 0.1 or 0.5 mm on request
with order. Normally closed output contact. Supply voltages: 12 Vdc or
24 Vdc ±10% / absorbed power 50 W.
HD2016 Weighing rain gauge, area 400 cm
2
. 3000 cc collecting reservoir. Automatic
water discharge. Operating temperature from +4 °C to +60 °C. RS485 Mod-
bus-RTU or SDI-12 output. Voltage-free output contact (NO). Power supply:
10…15 Vdc. Adjustable feet for ground installation included in the kit.