background image

 

HD32MT.3 

-   21   -

 

V1.2

 

WAIT!    MODEM 

 

shutdown is in 

 

progress 

 

  

3.

 

Wait for GSM/UMTS module shutdown, then remove the SIM card. 

MODEM IS OFF 

 

SIM CARD is free 

 

ESC when done 

 

  

4.

 

Wait for automatic exit from menu or press ESC to exit menu immediately. 

Resetting of rainfall quantity partial counter 
1.

 

Enter menu. The item "Reset INCR.Count" is shown. 

Reset INCR.Count 

 

Enter to confirm 

 

 

 

 

NEVER  REMOVE  SD   

2.

 

Press ENTER again to confirm that you want to reset the rainfall quantity partial counter, 

or press ESC  to exit.  The  data  logger automatically exits the menu if  ENTER  is not 

pressed within 15 seconds. 

CONFIRM THAT YOU   

want to clear 

 

the Rain Counter 

 

  

3.

 

Press ENTER again to confirm that you want to clear the rainfall quantity partial counter 

or press ESC to exit.  The data logger automatically exits the menu if ENTER is not 

pressed within 15 seconds. 

INCR. COUNTER 

WAS RESET 

 

 

  

4.

 

After reset, the data logger automatically exits the menu. 

 

Содержание HD32MT.3































































Отзывы: