Dell Studio One 19/1909 Скачать руководство пользователя страница 47

Страница: 47 / 53

Great user manuals database on

UserManuals.info

Remove the 2-pin jumper plug from pins 2 and 3 and fix it on pins 1 and 2.

Wait for approximately five seconds to clear the password setting.

Remove the 2-pin jumper plug from pins 1 and 2 and replace it on pins 2 and 3.

Replace the stand (see

Replacing the Stand

10.

Replace the shield (see

Replacing the Shield

11.

Replace the computer cover (see

Replacing the Computer Cover

12.

Connect your computer and devices to electrical outlets, and turn them on.

Clearing CMOS Settings

Follow the procedures in

Before You Begin

Remove the computer cover (see

Removing the Computer Cover

Removing the shield (see

Removing the Shield

Remove the stand (see

Removing the Stand

Remove the back I/O panel (see

Removing the Back I/O Panel

Locate the 3-pin CMOS connector (CLR_CMOS) on the system board (see

System Board Components

WARNING:

Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer.

WARNING:

The computer must be disconnected from the electrical outlet to clear the CMOS setting.

Содержание Studio One 19/1909






















































Результаты поиска

Содержание Studio One 19/1909

Отзывы:

Похожие инструкции для Studio One 19/1909

Бренды по названию

Популярные бренды

Dell Studio One 19/1909, Руководство по обслуживанию

Результаты поиска

Содержание Studio One 19/1909

Отзывы:

Похожие инструкции для Studio One 19/1909

Бренды по названию

Популярные бренды