Dell Studio One 19/1909 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 53

background image

Great user manuals database on

UserManuals.info

Replacing the Hard Drive

1.

Follow the procedures in

Before You Begin

2.

Prepare the new hard drive for installation and check the documentation that accompanied the drive to verify that the drive is configured for your
computer.

3.

Align the screws holes on the hard drive with the screw holes on the hard drive carrier.

4.

Replace the four screws that secure the hard drive to the hard drive carrier.

5.

Reconnect the hard drive connector to the hard drive.

6.

Slide the hard drive carrier into the grooves in the chassis.

7.

Align the screw holes on the hard drive carrier with the screw holes on the chassis.

8.

Tighten the two captive screws that secures the hard drive carrier to the chassis.

9.

Replace the shield (see

Replacing the Shield

10.

Replace the computer cover (see

Replacing the Computer Cover

Removing the Optical Drive

1.

Follow the procedures in

Before You Begin

2.

Remove the computer cover (see

Removing the Computer Cover

3.

Remove the shield (see

Removing the Shield

).

4.

Remove the stand (see

Removing the Stand

5.

Remove the back I/O panel (see

Removing the Back I/O Panel

6.

Remove the processor fan (see

Removing the Processor Fan

7.

Remove the right speaker (see

Removing the Right Speaker

8.

Disconnect the optical drive connector.

9.

Remove the three screws securing the optical drive carrier to the chassis and slide the optical drive carrier out of the computer.

1

hard drive

2

screws (4)

3

hard drive carrier

NOTE:

If you are not replacing the optical drive at this time, disconnect the other end of the data cable (SATA_2) and power cable (ODD_POWER)

from the system board and set it aside.

«
...
12
13
14
15
16
...
»

Содержание Studio One 19/1909






















































Отзывы:

Нет отзывов

Похожие инструкции для Studio One 19/1909

Бренд: Igel Страницы: 2

Бренд: Radio Shack Страницы: 52

Бренд: WinSystems Страницы: 53

PC 300GL Type 6561

Бренд: IBM Страницы: 66

Бренд: Digital Equipment Страницы: 321

Бренд: Montezuma Страницы: 24

Бренд: IBASE Technology Страницы: 87

Бренд: Vivo Страницы: 12

Бренд: Uplift Desk Страницы: 12

Бренд: Aplex Страницы: 69

ThinkCentre M920s

Бренд: Lenovo Страницы: 80

ThinkCentre M725s

Бренд: Lenovo Страницы: 72

ThinkCentre M720s

Бренд: Lenovo Страницы: 80

ThinkCentre M720t

Бренд: Lenovo Страницы: 86

ThinkCentre M72e

Бренд: Lenovo Страницы: 140

ThinkCentre Edge 71

Бренд: Lenovo Страницы: 230

Shadow Premier 8009-8325-30-01

Бренд: Vicon Страницы: 2

Бренд: Shuttle Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды