Dell Studio One 19/1909 Скачать руководство пользователя страница 42

Страница: 42 / 53

Great user manuals database on

UserManuals.info

Back to Contents Page

System Fan and Heat Sink Assembly

Dell Studio One 19/1909 Service Manual

Removing the System Fan and Heat Sink Assembly

Replacing the System Fan and Heat Sink Assembly

Removing the System Fan and Heat Sink Assembly

Follow the procedures in

Before You Begin

Remove the computer cover (see

Removing the Computer Cover

Remove the shield (see

Removing the Shield

Remove the stand (see

Replacing the Stand

Remove the back I/O panel (see

Removing the Back I/O Panel

Remove the three screws securing the system fan to the system board.

Loosen the two captive screws securing the heat sink to the system board.

Slide and lift the system fan away from the frame of the computer.

Disconnect the system fan cable from the connector (SYS_FAN1) on the system board.

WARNING:

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.

WARNING:

Do not touch the fan when the computer is powered on.

CAUTION:

Do not perform the following steps unless you are familiar with hardware removal and replacement. Performing these steps

incorrectly could damage your system board. For technical service information, see the

Setup Guide

CAUTION:

The heat sink assembly may be very hot during normal operation. Be sure that it has had sufficient time to cool before you touch it.

Содержание Studio One 19/1909






















































Результаты поиска

Содержание Studio One 19/1909

Отзывы:

Похожие инструкции для Studio One 19/1909

Бренды по названию

Популярные бренды

Dell Studio One 19/1909, Руководство по обслуживанию

Результаты поиска

Содержание Studio One 19/1909

Отзывы:

Похожие инструкции для Studio One 19/1909

Бренды по названию

Популярные бренды