Dell Studio 1569 Скачать руководство пользователя | Manualshive

Страница: 17 / 47

background image

Replacing the Display Assembly

1.

Follow the procedures in

Before You Begin

2.

Use the alignment posts to place the display assembly on the computer base.

3.

Replace the five screws that secure the display assembly to the computer base.

4.

Replace the display cable grounding screw in the display hinge.

5.

Route the Mini-Card antenna cables in the routing guides on the computer base.

6.

Follow the instructions from

Replacing the System Board

7.

Replace the battery (see

Replacing the Battery

Display Bezel

Removing the Display Bezel

1.

Follow the procedures in

Before You Begin

2.

Remove the display assembly (see

Removing the Display Assembly

).

3.

Remove the four rubber pads that cover the display bezel screws.

4.

Remove the fours screws that secure the display bezel to the display assembly.

5.

Carefully pull up along the edges of the display bezel to remove it from the display assembly.

1

Mini-Card antenna cables

2

computer base

CAUTION:

Before turning on the computer, replace all screws and ensure that no stray screws remain inside the computer. Failure to do so may

result in damage to the computer.

CAUTION:

The display bezel is extremely fragile. Be careful when removing it to prevent damaging the bezel.

«
...
15
16
17
18
19
...
»

Содержание Studio 1569
















































Отзывы:

Нет отзывов

Похожие инструкции для Studio 1569

Mac Mini Model A1347

Бренд: iFixit Страницы: 13

PC 300PL Types 6862

Бренд: IBM Страницы: 112

Бренд: Worx Professional Страницы: 106

Бренд: eMachines Страницы: 36

ARK-3531 Series

Бренд: Advantech Страницы: 84

6868 - IntelliStation M - Pro

Бренд: IBM Страницы: 188

Бренд: UUGear Страницы: 25

Бренд: IBASE Technology Страницы: 22

SR5605F - Presario - 1 GB RAM

Бренд: Compaq Страницы: 1

Rosemount TankRadar SCC 5320

Бренд: Emerson Страницы: 4

Бренд: Emerson Страницы: 108

Бренд: Korg Страницы: 33

Бренд: Asus Страницы: 28

Barebone System A7VT400

Бренд: Asus Страницы: 98

Бренд: Asus Страницы: 20

Бренд: Asus Страницы: 44

Бренд: Asus Страницы: 104

Barebone System T2-PH2

Бренд: Asus Страницы: 114

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды