Dell Studio 1569 Скачать руководство пользователя страница 44

Страница: 44 / 47

15.

Replace the Bluetooth card (see

Replacing the Bluetooth Card

16.

Replace the palm rest (see

Replacing the Palm Rest

17.

Replace the power button panel (see

Replacing the Power Button Panel

18.

Replace the keyboard (see

Replacing the Keyboard

19.

Replace the Mini-Card(s) (see

Replacing the Mini-Card(s)

20.

Replace the memory module(s) (see

Replacing the Memory Module(s)

21.

Replace the battery (see

Replacing the Battery

22.

Turn on the computer.

23.

Enter the service tag (see

Entering the Service Tag in the BIOS

Entering the Service Tag in the BIOS

Ensure that the AC adapter is plugged in and that the main battery is installed properly.

Turn on the computer.

Press <F2> during POST to enter the system setup program.

Navigate to the security tab and enter the service tag in the

Set Service Tag

field.

Back to Contents Page

CAUTION:

Before turning on the computer, replace all screws and ensure that no stray screws remain inside the computer. Failure to do so may

result in damage to the computer.

NOTE:

After you have replaced the system board, enter the computer's Service Tag into the BIOS of the replacement system board.

Содержание Studio 1569
















































Результаты поиска

Содержание Studio 1569

Отзывы:

Похожие инструкции для Studio 1569

Бренды по названию

Популярные бренды

Dell Studio 1569, Руководство по обслуживанию

Результаты поиска

Содержание Studio 1569

Отзывы:

Похожие инструкции для Studio 1569

Бренды по названию

Популярные бренды