Dell Studio 1569 Скачать руководство пользователя страница 47

Страница: 47 / 47

Replacing the USB/Audio Board

Follow the procedures in

Before You Begin

Place the USB/audio board on the computer base.

Replace the three screws that secure the USB/audio board to the computer base.

Slide the audio cable into the USB/audio board connector and press down on the connector latch to secure the cable.

Connect the speaker cable to the USB/audio board connector.

Connect the USB cable to the USB/audio board connector.

Replace the palm rest (see

Replacing the Palm Rest

Replace the keyboard (see

Replacing the Keyboard

Replace the power button panel (see

Replacing the Power Button Panel

10.

Replace the battery (see

Replacing the Battery

Back to Contents Page

CAUTION:

Before turning on the computer, replace all screws and ensure that no stray screws remain inside the computer. Failure to do so may

result in damage to the computer.

Содержание Studio 1569
















































Результаты поиска

Содержание Studio 1569

Отзывы:

Похожие инструкции для Studio 1569

Бренды по названию

Популярные бренды

Dell Studio 1569, Руководство по обслуживанию

Результаты поиска

Содержание Studio 1569

Отзывы:

Похожие инструкции для Studio 1569

Бренды по названию

Популярные бренды