Dell Studio 1569 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 47

background image

6.

Pull the pull-tab to disconnect the display cable from the display panel.

Replacing the Display Panel

1.

Follow the procedures in

Before You Begin

2.

Connect the display cable to the connector on the back of the display panel.

3.

Use the alignment posts to place the display panel on the display cover.

4.

Replace the four screws that secure the display panel to the display cover.

5.

Replace the display bezel (see

Replacing the Display Bezel

6.

Replace the display assembly (see

Replacing the Display Assembly

7.

Replace the battery (see

Replacing the Battery

Display Hinges and Brackets

1

screws (4)

2

display panel

3

display cover

1

display panel

2

pull-tab

3

display cable

CAUTION:

Before turning on the computer, replace all screws and ensure that no stray screws remain inside the computer. Failure to do so may

result in damage to the computer.

«
...
17
18
19
20
21
...
»

Содержание Studio 1569
















































Отзывы:

Нет отзывов

Похожие инструкции для Studio 1569

Бренд: Gateway Страницы: 42

Бренд: EBN Страницы: 9

Deep Silence 6 Revision B

Бренд: Nanoxia Страницы: 24

Бренд: Displays2go Страницы: 2

Бренд: Rousseau Страницы: 7

Бренд: Compal Страницы: 57

Бренд: Worx Professional Страницы: 106

Бренд: Cartft Страницы: 10

Бренд: Dell Страницы: 94

Бренд: Unitron Страницы: 19

Бренд: JNC Страницы: 58

Бренд: Shuttle Страницы: 11

Бренд: U-Line Страницы: 12

Бренд: U-Line Страницы: 21

Бренд: U-Line Страницы: 24

Бренд: Aaeon Страницы: 132

Бренд: Aaeon Страницы: 66

Бренд: IBASE Technology Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды