Dell PowerEdge T100 Скачать руководство пользователя страница 25

Страница: 25 / 160

About Your System

SATA port A/B/C/D

hard disk drive

failure

SATA port A/B/C/D

hard disk drive

auto-sensing error

Faulty drive. INT13 call
failure from the drive.

Ensure that the hard drive
cables are properly
connected. See
"Troubleshooting a Hard
Drive" on page 124.

SATA Port A/B/C/D

hard disk not found

SATA Port A/B/C/D set as
Auto, no disk installed.

Run the System Setup
program to correct the
settings. See "Using the
System Setup Program" on
page 29.

Sector not found

Seek error

Seek operation

failed

Faulty diskette or hard
drive.

See "Troubleshooting a
USB Device" on page 110
or "Troubleshooting a Hard
Drive" on page 124 for the
appropriate drive installed
in your system.

Shutdown failure

Shutdown test failure.

Ensure that all memory
modules are properly
installed. See
"Troubleshooting System
Memory" on page 118. If
the problem persists, see
"Getting Help" on
page 141.

The amount of

system memory has

changed.

Faulty memory module.

Information only, if you
have changed the memory
configuration.

See "Troubleshooting
System Memory" on
page 118. If the problem
persists, see "Getting Help"
on page 141.

Faulty memory module.

See "Troubleshooting
System Memory" on
page 118. If the problem
persists, see "Getting Help"
on page 141.

Table 1-6.

System Messages

(continued)

Message

Causes

Corrective Actions

book.book Page 25 Wednesday, June 24, 2009 8:21 AM

Содержание PowerEdge T100

































































































































































Результаты поиска

Содержание PowerEdge T100

Отзывы:

Похожие инструкции для PowerEdge T100

Бренды по названию

Популярные бренды

Dell PowerEdge T100, Руководство владельца оборудования

Результаты поиска

Содержание PowerEdge T100

Отзывы:

Похожие инструкции для PowerEdge T100

Бренды по названию

Популярные бренды