Dell PowerEdge T100 Скачать руководство пользователя страница 19

Страница: 19 / 160

About Your System

Data error

The diskette drive or hard
drive cannot read the data.

For the operating system,
run the appropriate utility
to check the file structure
of the diskette drive or hard
drive.

See your operating system
documentation for
information on running
these utilities.

Decreasing

available memory

One or more memory
modules might be
improperly seated or faulty.

Reinstall the memory
modules and, if necessary,
replace them. See
"Memory" on page 76.

See "Troubleshooting
System Memory" on
page 118.

Diskette read

failure

Faulty or improperly
inserted diskette.

Replace the diskette.

Diskette subsystem

reset failed

Faulty diskette drive or
optical drive controller.

Ensure that the diskette
drive and optical drive
cables are properly
connected. See
"Troubleshooting a USB
Device" on page 110 and
"Troubleshooting an
Optical Drive" on page 122.
If the problem persists, see
"Getting Help" on
page 141.

Drive not ready

Diskette missing or
improperly inserted in
diskette drive.

Reinsert or replace the
diskette.

Table 1-6.

System Messages

(continued)

Message

Causes

Corrective Actions

book.book Page 19 Wednesday, June 24, 2009 8:21 AM

Содержание PowerEdge T100

































































































































































Результаты поиска

Содержание PowerEdge T100

Отзывы:

Похожие инструкции для PowerEdge T100

Бренды по названию

Популярные бренды

Dell PowerEdge T100, Руководство владельца оборудования

Результаты поиска

Содержание PowerEdge T100

Отзывы:

Похожие инструкции для PowerEdge T100

Бренды по названию

Популярные бренды