Dell PowerConnect B-8000 Скачать руководство пользователя

Страница: 45 / 58

PowerConnect B-8000 Hardware Reference Manual

53-1001788-01

Environmental requirements

Table 9

lists the acceptable environmental ranges for both operating and nonoperating (such as

during transportation or storage) conditions.

General specifications

Table 10

lists the general specifications for the PowerConnect B-8000.

Input system power (including power supply and fan
FRUs)

Idle: 206 W
Maximum: 306 W

Input voltage

85-264 VAC

Input line frequency

47-63 Hz

BTU rating

1044.11 BTU/hr

Inrush current

Maximum of 60A for period of 10-150mS

Input line protection

Both AC lines are fused

TABLE 8

Power Supply Specifications

Specification Value

TABLE 9

Environmental requirements

Condition

Acceptable during operation

Acceptable During Non-Operation

Ambient
Temperature

0º to 40º C
32º to 104º F

-25º to 70º C
-13º to 158º F

Humidity

10% to 85% RH non-condensing, at
40º C (104º F)

10% to 90% RH non-condensing, at 70º C
(158º F)

Altitude

0 to 3 km (9,842 feet) above sea level

0 to 12 km (39,370 feet) above sea level

Shock

20 G, 6 ms, half-sine wave

33 G, 11 ms, half-sine wave, 3/eg Axis

Vibration

0.5 G sine, 0.4 gms random, 5-500 Hz

2.0 G sine, 1.1 gms random, 5-500 Hz

Air flow

Maximum - 71.36 cmh (42 cfm)
Nominal - 59.47 cmh (35 cfm)

Heat dissipation

1044 BTU/hr (32 port configuration)

TABLE 10

General specifications

Specification

Description

Configurable port types

F_Port, FL_Port, E_Port, and M_Port

System architecture

Nonblocking shared-memory switch

System processor

Freescale MPC8548 x 1.3GHz

ANSI Fibre Channel protocol

FC-PH (Fibre Channel Physical and Signalling Interface standard)

Modes of operation

Fibre Channel Class 2 and Class 3

Fabric initialization

Complies with FC-SW-3 Rev. 6.6

FC-IP (IP-over-Fibre Channel)

Complies with FC-IP 2.3 of FCA profile

Содержание PowerConnect B-8000



























































Результаты поиска

Содержание PowerConnect B-8000

Отзывы:

Похожие инструкции для PowerConnect B-8000

Бренды по названию

Популярные бренды

Dell PowerConnect B-8000, Справочник по аппаратуре

Результаты поиска

Содержание PowerConnect B-8000

Отзывы:

Похожие инструкции для PowerConnect B-8000

Бренды по названию

Популярные бренды