Dell PowerConnect B-8000 Скачать руководство пользователя | Manualshive

Страница: 50 / 58

background image

38

PowerConnect B-8000 Hardware Reference Manual

53-1001788-01

Regulatory compliance

A

The standards compliance label on the PowerConnect B-8000 contains the CE mark which
indicates that this system conforms to the provisions of the following European Council directives,
laws, and standards:

•

Electromagnetic Compatibility (EMC) Directive 2004/108/EEC

•

Low Voltage Directive (LVD) 2006/95/EC

•

EN50082-2/EN55024:1998 (European Immunity Requirements)

-

EN61000-3-2/JEIDA (European and Japanese Harmonics Spec)

-

EN61000-3-3

Canadian requirements

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations, ICES-003 Class A.

Laser compliance

This equipment contains Class 1 laser products and complies with FDA Radiation Performance
Standards, 21 CFR Subchapter I and the international laser safety standard IEC 825-2.

ATTENTION

Use only optical transceivers that are qualified by Brocade Communications Systems, Inc. and
comply with the FDA Class 1 radiation performance requirements defined in 21 CFR Subchapter I,
and with IEC 825-2. Optical products that do not comply with these standards might emit light that
is hazardous to the eyes.

RTC battery

CAUTION

Do not attempt to replace the real-time clock (RTC) battery. There is danger of explosion if the
battery is incorrectly replaced or disposed of. Contact your switch supplier if the real-time clock
begins to lose time.

Electrical safety

CAUTION

This switch might have more than one power cord. To reduce the risk of electric shock,
disconnect both power cords before servicing.

«
...
48
49
50
51
52
...
»

Содержание PowerConnect B-8000



























































Отзывы:

Нет отзывов

Похожие инструкции для PowerConnect B-8000

Бренд: Keithley Страницы: 434

SmartSwitch 6500

Бренд: Cabletron Systems Страницы: 150

MMAC-Plus 9H421-12

Бренд: Cabletron Systems Страницы: 38

Бренд: Cabletron Systems Страницы: 86

MMAC-Plus 9T125-24

Бренд: Cabletron Systems Страницы: 30

7C03 MMAC SmartSWITCH

Бренд: Cabletron Systems Страницы: 16

Бренд: Idem Страницы: 2

Бренд: hager Страницы: 2

Бренд: hager Страницы: 4

Бренд: hager Страницы: 2

1big Dock SSD Pro

Бренд: LaCie Страницы: 28

Бренд: D-Link Страницы: 242

S5170-EI Series

Бренд: H3C Страницы: 46

Бренд: BeeSecure Страницы: 35

Бренд: Kramer Страницы: 8

Бренд: ADDER Страницы: 46

Allen-Bradley 194U Series

Бренд: Rockwell Automation Страницы: 2

Бренд: Thinklogical Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды