Dell PowerConnect B-8000 Скачать руководство пользователя | Manualshive

Страница: 37 / 58

background image

PowerConnect B-8000 Hardware Reference Manual

25

53-1001788-01

Chapter

4

Removal and Replacement Procedures (RRPs)

In this chapter

•

RRP: Power supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

•

RRP: Fan assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Introduction

NOTE

Read the

“Installation and safety considerations”

before servicing.

The field replaceable units (FRUs) in the Powerconnect B-8000 can be removed and replaced
without special tools. The PowerConnect B-8000 can continue operating during many of the FRU
replacements if the conditions specified in the procedure are followed.

The following sections contain FRU removal and replacement procedures (RRPs).

RRP: Power supply

The PowerConnect B-8000 has two power supplies, as displayed in

. Fabric OS identifies

the power supplies from right to left on the non-port side as power supply 1 and power supply 2.
(The actual appearance of the PowerConnect B-8000 may differ from this illustration but the
locations are correct.)

FIGURE 6

Switch power supplies on the non-port side

CAUTION

Disassembling any part of the power supply voids the part warranty and regulatory certifications.
There are no user-serviceable parts inside the power supply. The cooling system relies on
pressurized air, do not leave either of the power supply slots empty longer than two minutes when

1

Power supply 1

2

Power supply 2

1

2

«
...
35
36
37
38
39
...
»

Содержание PowerConnect B-8000



























































Отзывы:

Нет отзывов

Похожие инструкции для PowerConnect B-8000

Бренд: D-Link Страницы: 4

Бренд: D-Link Страницы: 2

S5560S-EI Series

Бренд: H3C Страницы: 37

OfficeConnect WX4400

Бренд: 3Com Страницы: 528

Pow-R-Line SPX0361126

Бренд: Eaton Страницы: 584

Бренд: AdLuminis Страницы: 8

Бренд: Dahua Страницы: 17

DigiTOOLS VS-41USB

Бренд: Kramer Страницы: 8

TK-205K - PS/2 KVM Switch

Бренд: TRENDnet Страницы: 11

Бренд: Farallon Страницы: 22

Бренд: StarTech.com Страницы: 2

Бренд: SMART-AVI Страницы: 2

Бренд: LEGRAND Страницы: 197

Бренд: Valcom Страницы: 1

Бренд: FIBERROAD Страницы: 30

Бренд: Hama Страницы: 14

Hidden Ignition Switch

Бренд: Booma-RC Страницы: 16

Бренд: ATEN Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды