Dell PowerConnect B-8000 Скачать руководство пользователя страница 4

Страница: 4 / 58

PowerConnect B-8000 Hardware Reference Manual

53-1001788-01

Cabinet installation for a PowerConnect B-8000 . . . . . . . . . . . . . . . . 8

PowerConnect B-8000 configuration. . . . . . . . . . . . . . . . . . . . . . . . . . 8

Providing power to the switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Creating a serial connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Switch IP address. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Date and time settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Brocade Inter-Switch Link (ISL) Trunking . . . . . . . . . . . . . . . . . . 13

Chapter 3

PowerConnect B-8000 Operation

In this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Powering the PowerConnect B-8000 on and off. . . . . . . . . . . . . . . . 15

LED activity interpretation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

PowerConnect B-8000 LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
LED locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
LED patterns. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

POST and boot specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

POST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Boot. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Interpreting POST results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

PowerConnect B-8000 Maintenance. . . . . . . . . . . . . . . . . . . . . . . . .20

Installing an SFP or SFP+ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

PowerConnect B-8000 Management . . . . . . . . . . . . . . . . . . . . . . . .22

Chapter 4

Removal and Replacement Procedures (RRPs)

In this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

RRP: Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

RRP: Fan assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Appendix A

PowerConnect B-8000 Specifications

In this appendix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Switch components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Weight and physical dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Facility requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Power supply specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Environmental requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

General specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Data transmission ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Fabric latency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Memory specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Fibre Channel port specifications . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Содержание PowerConnect B-8000



























































Результаты поиска

Содержание PowerConnect B-8000

Отзывы:

Похожие инструкции для PowerConnect B-8000

Бренды по названию

Популярные бренды

Dell PowerConnect B-8000, Справочник по аппаратуре

Результаты поиска

Содержание PowerConnect B-8000

Отзывы:

Похожие инструкции для PowerConnect B-8000

Бренды по названию

Популярные бренды