Dell PowerConnect B-8000 Скачать руководство пользователя | Manualshive

Страница: 44 / 58

background image

32

PowerConnect B-8000 Hardware Reference Manual

53-1001788-01

Weight and physical dimensions

A

Weight and physical dimensions

lists the weight and dimensions of the PowerConnect B-8000.

Facility requirements

provides the facilities requirements that must be met for the PowerConnect B-8000.

Power supply specifications

The power supplies are universal and capable of functioning worldwide without voltage jumpers or
switches. They meet IEC 61000-4-5 surge voltage requirements and are autoranging in terms of
accommodating input voltages and line frequencies. Each power supply has a built-in fan for
cooling, pushing air towards the port side of the switch.

lists the power supply specifications for the PowerConnect B-8000.

TABLE 6

Physical specifications

Dimension

Value

Height

1U or 4.3 cm (1.7 in.)

Depth

63.4 cm (25 in.)

Width

42.8 cm (16.8 in.)

Weight (with two power supplies, three fan assemblies,
and no SFPs installed)

12.97 kg (28.6 lb)

TABLE 7

Facility Requirements

Type

Requirements

Electrical

•

Primary AC input 100-240 VAC, 2.0A, 47-63 Hz; switch autosenses input voltage

•

Adequate supply circuit, line fusing, and wire size, as specified by the electrical rating
on the switch nameplate

•

Circuit protected by a circuit breaker and grounded in accordance with local electrical
codes

Refer to

Table 8 on page 32

for complete power supply specifications.

Thermal

•

A minimum air flow of 79.8 cubic meters/hour (47 cubic ft/min.) available in the
immediate vicinity of the switch

•

Ambient air temperature not exceeding 40



C (104



F) while the switch is operating

Cabinet (when
rack-mounted)

•

One rack unit (1U) in a 48.3 cm (19-inch) cabinet

•

All equipment in cabinet grounded through a reliable branch circuit connection

•

Additional weight of switch not to exceed the cabinet’s weight limits

•

Cabinet secured to ensure stability in case of unexpected movement

TABLE 8

Power Supply Specifications

Specification Value

Maximum output of one power supply

350 watts

System DC power consumption (excluding power supply
and fan FRUs)

Idle: 182.4 W
Maximum: 306 W

«
...
42
43
44
45
46
...
»

Содержание PowerConnect B-8000



























































Отзывы:

Нет отзывов

Похожие инструкции для PowerConnect B-8000

Бренд: 3Com Страницы: 128

Бренд: 3Com Страницы: 2

Бренд: 3Com Страницы: 422

3CR16708-91 - OfficeConnect Managed Switch 9

Бренд: 3Com Страницы: 4

Бренд: 3Com Страницы: 5

Бренд: 3Com Страницы: 30

Бренд: 3Com Страницы: 36

Бренд: 3Com Страницы: 4

Baseline 2226-PWR Plus

Бренд: 3Com Страницы: 77

Бренд: 3Com Страницы: 570

OfficeConnect WX1200

Бренд: 3Com Страницы: 28

Baseline 2226-PWR Plus

Бренд: 3Com Страницы: 4

CoreBuilder 6000

Бренд: 3Com Страницы: 31

Бренд: G&D Страницы: 36

S5500-SI Series

Бренд: H3C Страницы: 130

S5500-EI series

Бренд: H3C Страницы: 19

S5500-EI series

Бренд: H3C Страницы: 91

S5500-EI series

Бренд: H3C Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды