Dell PowerConnect B-8000 Скачать руководство пользователя

Страница: 51 / 58

PowerConnect B-8000 Hardware Reference Manual

53-1001788-01

Regulatory certifications

CAUTION

Connect the power cord only to a grounded outlet.

CAUTION

This product is designed for an IT power system with phase-to-phase voltage of 230V. After
operation of the protective device, the equipment is still under voltage if it is connected to an IT
power system.

Regulatory certifications

Table 15

lists the regulatory compliance standards for which the PowerConnect B-8000 is certified.

TABLE 15

Regulatory compliance standards

Country

Standards

Agency Certifications and Markings

Safety

EMC

Safety

EMC

United States

Bi-Nat UL/CSA 60950-1
1st Ed or latest

ANSI C63.4

cCSAus

FCC Class A and
Statement

Canada

Bi-Nat UL/CSA 60950-1
1st Ed or latest

ICES-003 Class A

cCSAus

ICES A and Statement

Japan

CISPR22 and JEIDA
(Harmonics)

VCCI-A and Statement

European Union

EN60950-1 or latest

EN55022 and EN55024 TUV-GS, N

CE marking

Australia, New Zealand

EN55022 and CISPR22
or AS/NZS CISPR22

C-Tick mark

Argentina

IEC60950-1 or latest

“S” mark

Russia

IEC60950-1 or latest

51318.22-99 and
51318.24.99 or latest

GOST mark

Korea

KN22 and KN24

KCC mark Class A

China (PS only)

GB4943-2001 and
GB9254-1998 or latest

GB17625.1-2003 or
latest

CCC logo

Taiwan (PS only)

CNS 14336(94) or latest CNS 13438(95) or latest BSMI mark

BSMI mark

Содержание PowerConnect B-8000



























































Результаты поиска

Содержание PowerConnect B-8000

Отзывы:

Похожие инструкции для PowerConnect B-8000

Бренды по названию

Популярные бренды

Dell PowerConnect B-8000, Справочник по аппаратуре

Результаты поиска

Содержание PowerConnect B-8000

Отзывы:

Похожие инструкции для PowerConnect B-8000

Бренды по названию

Популярные бренды