
Using the CLI
155
• Enables CLI login and HTTP access to use the local authentication setting
only, which allows user account access via these management interfaces.
The user may return later to configure Radius or .
• Sets up the IP address for the management VLAN or enables support for
DHCP to configure the management IP address dynamically.
• Sets up the SNMP community string to be used by the SNMP manager.
The user may choose to skip this step if SNMP management is not used. If
it is configured, the default access level is set to the highest available
access for the SNMP management interface. The user may return later to
add to the community string or reconfigure the access level of the
community string. Initially only SNMPv1/2c will be activated. SNMPv3 is
disabled until the user returns to configure security access for SNMPv3
(for example, engine ID, view, and so on). The SNMP community string
may include spaces. The wizard requires the use of quotation marks when
the user wants to enter spaces in the community string. Although spaces
are allowed in the community string, their use is discouraged. The default
community string contains no spaces.
• Allows the user to specify the management server IP or permit SNMP
access from all IP addresses.
• Sets up the default gateway IP address.
If the user chooses not to use the wizard initially, the session defaults to the
CLI mode with a warning to refer the documentation. During a subsequent
login, the user may again elect not to run the setup wizard. Once the wizard
has established configuration, however, the wizard is presented only if the
user resets the switch to the factory default settings. While the wizard is
running, the system does not display any unsolicited or unrelated status
messages. For example, the system does not display event notification or
system status messages.
After completing the wizard, the user is given a chance to save his
configuration and continue to the CLI. If the user chooses to discard his
configuration, any restart of the wizard must be from the beginning. When
the user chooses to restart the wizard, any configuration the user saved
previously automatically is offered for the user to accept. The user may elect
to correct only a few items instead of re-entering all the data.
Содержание PowerConnect 6224
