Dell Latitude 5430 Скачать руководство пользователя

Страница: 17 / 139

Steps

1. Slide the battery release latch to the unlock position.
2. Slide the latch down to unlock the battery.
3. Lift the battery out of the battery bay.
4. Remove the battery from the system.

Installing the batteries

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

NOTE:

Latitude 5430 Rugged can accommodate two hot-swap capable batteries (Primary and optional). The installation

procedure of the primary and optional battery are identical.

NOTE:

BIOS displays a Battery error when non-Latitude 5430 Rugged batteries are used.

The following image indicates the location of the battery and provides a visual representation of the installation procedure.

Removing and installing components

Содержание Latitude 5430












































































































































Результаты поиска

Содержание Latitude 5430

Отзывы:

Похожие инструкции для Latitude 5430

Бренды по названию

Популярные бренды

Dell Latitude 5430, Руководство по обслуживанию

Результаты поиска

Содержание Latitude 5430

Отзывы:

Похожие инструкции для Latitude 5430

Бренды по названию

Популярные бренды