Dell Latitude 5430 Скачать руководство пользователя

Страница: 127 / 139

Table 21. System setup options—System Management menu (continued)

System Management

By default

OFF

option is disabled.

USB Provision

Enable USB Provision

Intel AMT can be provisioned using the local provisioning file using a USB
storage device.

By default

OFF

option is disabled.

Table 22. System setup options—Keyboard menu

Keyboard

Fn Lock Options

By default, the Fn lock option is enabled.

Lock Mode

By default, the

Lock Mode Secondary

option is enabled. With this option, the

F1-F2 keys scan the code for their secondary functions.

Keyboard Illumination

Enables to change the keyboard illumination settings.

By default, the

Level is 100%

option is enabled.

Keyboard Backlight Timeout on AC

Set the timeout value for the keyboard backlight when an AC adapter is
connected to the system.

By default, the

10 seconds

option is enabled.

Keyboard Backlight Timeout on
Battery

Set the timeout value for the keyboard backlight when the is running only on
battery power.

By default, the

10 seconds

option is enabled.

Device Configuration Hotkey Access

Manages whether you can access device configuration screens through
hotkeys during system startup.

By default, the option is enabled.

RGB Keyboard Backlight

Configures the RGB keyboard backlight feature.

By default, the

White

Red

Green

Blue

are enabled.

Table 23. System setup options—Pre-boot Behavior menu

Pre-boot Behavior

Adapter Warnings

Enable Adapter Warnings

Enable or disable the warning messages during boot when the adapters with
less power capacity are detected.

By default, the option is enabled.

Warning and Errors

Enable or disable the action to be done when a warning or error is encountered.

By default, the

Prompt on Warnings and Errors

option is enabled.

USB-C Warnings

Enable Dock Warning Messages

By default, the option is enabled.

Fastboot

Allows you to configure the speed of the UEFI boot process.

By default, the

Minimal

option is enabled.

Extend BIOS POST Time

Set the BIOS POST load time.

By default, the

0 seconds

option is enabled.

MAC Address Pass-Through

Replaces the external NIC MAC address with the selected MAC address from
the system.

BIOS setup

127

Содержание Latitude 5430












































































































































Результаты поиска

Содержание Latitude 5430

Отзывы:

Похожие инструкции для Latitude 5430

Бренды по названию

Популярные бренды

Dell Latitude 5430, Руководство по обслуживанию

Результаты поиска

Содержание Latitude 5430

Отзывы:

Похожие инструкции для Latitude 5430

Бренды по названию

Популярные бренды